gso rc8 3d models

Slic3r 1.3 rc8 was used with support for the outer ring only, as inner structures don't need support. Three perimeters and three solid layers were printed, along with top infill that's concentric. Post-Printing Remove Support Remove support from the...

Hello everyone,\r\nHere is the stable evolution of Marlin 1.1.4 for DiscoEasy 200.\r\nIt's configured for a factory-new DiscoEasy200 with screen.\r\nNo need to recable anything this time (Thanks Jey!).\r\n\r\nActivated options:\r\n- Auto bed leveling...

I have also incorporated my HyperCube Marlin V1.1 RC8 Configuration.h file for users' reference. Please ensure compatibility before utilizing it. My setup utilizes an MKS Gen V1.4 controller. ... Most Recently, I've updated the Simplify 3D Factory file...

Here is the BOM list: Top V1: - 2 M2x16 bolts and nuts - 3 M3X16 bolts and nuts Top V2: - 2 M2x16 bolts and nuts - 2 M3X16 bolts and nuts Bottom V1: - 3 M3X16 bolts and nuts Bottom V2: - 2 M3X16 bolts and nuts If you need a firmware, I have an RC8...

If using Marlin firmware, consider updating to version 1.1.0 RC8 or later for improved performance. Printer Settings: Anycubic I3 Rafts: No Supports: No Resolution: 0.2 Infill: 25-30% Notes: To achieve the best print position for the probe...

Update 16/3/2107: My Marlin RC8 Firmware configuration has been added. ... Print Settings: Printer: Wanhao Duplicator i3 V2 Rafts: No Supports: No Resolution: 200 microns Infill: 30% Notes: 5 Top Solid Layers 3 Bottom Solid Layers 4 Outline/Perimeter...

On 09-03-17, I fixed a bug in Marlin 1.1.0 RC8 for Anet A6 printers. Firmware files are available at https://github.com/JohnnyTheOne/MarlinAnetA6. To finish the setup, you just need to set the z-offset after flashing. The 18mm sensor position is X...

The sensor itself is connected to the unused E-stop connector on the Printrboard, and Marlin version 1.0.0-RC8 is used with three point bed measuring. Adding a 'G29' command after 'G28' in the G-code runs the bed levelling procedure before each...

BLTouch is compatible with RC8 and later version of Marlin firmware. You need to activate the BLTouch functionality inside the firmware. We provided a sample firmware to show how the BLTouch was configured (check configuration.h). The 3 pins...

Fits dual-speed knobs made in the style of GSO, featuring a 37mm OD fine-focus dial and a hole precisely designed for a 4mm OD focuser shaft. This product also fits SkyWatcher-style 3.75mm OD shafts and possibly other types as well. The accompanying...

A 3D printable F5 Newtonian telescope with an open or closed frame design and support for autofocusing designed for astrophotography or visual observing. Designed to support A6 inch primary mirror and can be customized to support multiple focal...

Latest stock Marlin version RC8 firmwares pre-configured for Anycubic Kossel and Kossel Plus are available on Google Drive from the user manual: https://drive.google.com/drive/folders/0B8VIB533cgdMSVMxNm43aG1OQ0U Files can be found in the folder...

Update 4/7/2017: I added my HyperCube Marlin V1.1 RC8 Configuration.h Be sure to check it for compatibility before using it. I'm running with an MKS Gen V1.4 controller. Update 1/17/2020: Added lastest Simplify 3D Factory file for my HyperCube...

Update 4/7/2017: I added my HyperCube Marlin V1.1 RC8 Configuration.h Be sure to check it for compatibility before using it. I'm running with an MKS Gen V1.4 controller. Update 1/17/2020: Added lastest Simplify 3D Factory file for my HyperCube...

Update2 (RC3.scad): Set the default back to r=30mm and updated the .stl Update3 (RC4.scad): Turned the lever ninety degrees again for easier printing of the axle mounting hole Update4 (RC5.scad): Bending lever is rounded only on the backside now as...

Applies to GSO 10" Dobsonians with premium Altitude bearing tension adjustment mechanism Apretura AD10, Zhummel Z10, Orion Sky Line 10" 8" and 12" telescope models of the same lineup will require a different belt and mild redesign of the motor-clamp...

I also have a GSO focuser laying around that I believe I pulled from an Orion ST-80A doublet I used to have. I decided that I could put that objective to use visually or with filters if I did decide to image with it. I took some measurements...

I also have a GSO focuser laying around that I believe I pulled from an Orion ST-80A doublet I used to have. I decided that I could put that objective to use visually or with filters if I did decide to image with it. I took some measurements and...

#### UPDATE * 2020-02-23 Add Config.h for OnStep 3.16 and Pulley_GT2-40v2.stl * 2020-10-09 New red edition add RA/DE belt gear box cover and more improved * 2020-12-12 Add GX16-4 ports version, PCB is on...

Configuration.h files have been updated to Marlin 1.1-RC8. Old file versions can be found on Thingiverse (http://www.thingiverse.com/thing:2013921). E3D (Inductive) Sensor Mount v1.1 provides improved sensor mount stability. New X_Carriage &...

And the induction sensor is not set up with this firmware, I do plan on upgrading this firmware to RC8 and adding the sensor and possibly redesigning the blower should there be any problems with induction sensor adjustment. With it all fitted, there...

But wait, there's more: - Now you need to parameterize your firmware (in my case, Marlin RC8) by modifying the extruder motor step rate. - First, invert the Nema's rotation direction (and yes, we put an gear in!). To do this, find the line in...

UPDATE 4: I've updated the link to the firmware I'm running on my Ramps 1.4 to Marlin 1.1.0 RC8 Bugfix. As always, do a PID tune and adjust your E-Steps accordingly. Mesh bed leveling is now enabled, and it works incredibly well. UPDATE 3: I've...

Amongst the major improvements to the firmware since 1.1.0-RC8 that I previously uploaded are improvements to overall auto-bed leveling (mesh-leveling, UBL, G26) performance, full BLTouch v3.0/3.1 compatibility as well as improved firmware stability...

**Software:** Arduino (for updating firmware) https://www.arduino.cc/en/Main/Software Cura 5.1 (for generating 3D printing codes) https://github.com/Ultimaker/Cura/releases/tag/5.1.0 FreeCAD (for designing 3D parts)...

Update 05-02-2017 So I had been using this for a while using marlin rc8 but was never totally satisfied with the calibration as even these latest versions of marlin do not allow a full range of delta calibration parameters. So I "downgraded" to...