gso focuser 3d models

This endeavor aimed to repurpose as much of the original equipment as possible, including the eyepiece holder, focuser knobs, metal plate securing the focuser knobs against the rack, metal coverplate, two screws holding those pieces in place on the...

A custom-designed clamp for securing a 2-inch Moonlite CR focuser on a portable telescope featuring an open tube design.

This project involves creating a user-friendly interface for adjusting the focus of a telescope using a hand-held controller connected to an Arduino board and LCD display.

a little evolution with a best fit in the 3" focuser. ...Perfect for camera, like 2600m with a 2" coma corrector

A new focuser knob/dial/wheel is available for Meade ETX125 telescopes, featuring a larger diameter grip for enhanced fine focus capabilities. The textured edge enables easy handling even when wearing gloves. ...Moreover, the main dial has strategically...

... the screws are designed for M4. The holes for adjusting screws (x2) have been threaded with a tool (M4). The bigger diameter for the adjusting ring must be put face to the camera. If not, the focuser will be thighten and won't be able to turn.

... rigid and precise. This focuser has a 2-inch diameter, a travel of 16 millimeters, and is compatible with 1:10 spincle reducers. Its spindle diameter measures 4 millimeters. ...The base plate radius accommodates tubes with a 250-millimeter diameter.

... EAF to the 3" Feather Touch focuser. ... In my case I used it to mount the ZWO AEF (https://astronomy-imaging-camera.com/product/zwo-eaf). It's reversible so you need to orient the holes such that they align with the two screw threads on the focuser.

Micro focuser and focus lock for Nikon 55-200mm zooom lens. Remixed to fit this lens and changed the hex head caps/adjusters to be the same. Hardware: (4) M40x30 hex head screws (2) M40 nuts -hammer in the hex head screws into the...

Celestron doesn't officially support their electronic focuser on the 5SE model so this fixes that. No modifications are necessary to any of the stock telescope or focuser components. Basic instructions are: 1. Print this thing out .. I used...

The dust cap has an inner diameter of 2.25 inches and fits snugly over the exterior of the draw tube on my Moonlite CR 2-inch Newtonian focuser. ...When printed at 100% scale, the fit was a bit too tight, so you may want to adjust your print settings...

After years of reliable service, my focus mechanism's rubber gaskets finally gave way. Determined to find a suitable replacement, I created a custom drop-in solution that closely mirrors its predecessor. ... Inner circumference: 40mm Thickness: 12mm

Protect the focus point with a protective cover, much like shielding the diagonal mirror or Barlow lens from harm. ...A sturdy design features three secure screw holes to ensure a solid hold.

The user-friendly design of this 1.25 focuser makes insertion a breeze, thanks to its cleverly angled bevel. ...Once in place, the secure grip provided by the ergonomic fingerhold ensures a confident removal, every time.

This focuser is a massive upgrade in functionality compared to any printed helical focuser. ...Attaches to the Hadley UTA by 4 M4x12 hexagon socket cap screws.For assembly instructions and rest of the files follow the linked original.Build tipsIf the...

... It's reversible so you need to orient the holes such that they align with the two screw threads on the focuser. Category: Physics & Astronomy

This model is designed for attaching an NEMA14 stepper motor to a Crayford double gear focuser. A toothed pulley with 52 GT2-2mm teeth has been created, connected via a 130-tooth belt to an aluminum pulley featuring 10 teeth. The PLA pulley is...

... the drilling of a setscrew hole on the side of the base that must be threaded to accept an M8 screw. An M8 nylon bolt is then screwed into place, serving as a tensioning mechanism and securing the focuser firmly in position when required.

This is a remix of a Precision Focuser for RedCat 51 from Wal20The holes for the nuts and the screws are designed for M4.The holes for adjusting screws (x2) have been threaded with a tool (M4). The bigger diameter for the adjusting ring must be put...

... a metal gear for the motor 4 M3 bolts to fix the motor on the box and the box on the support. Also 2 M4 bolts for the support on the base. Many arduino projects use step motor as electronic focuser. ... I used EQFocuser and I'm fully satisfied.

I got my scope second hand and it was missing the cap for the focuser, so I made this one that covers the focuser, and 1.25" adapter. There are L shaped slots cut out to go over the set screw knobs so that the cap can be locked in place. Loosen...

This is a remix of part C of the great ZWO OAG HELICAL FOCUSER, adapted to fit the Lowspec spectrograph, https://www.thingiverse.com/thing:2455390. I joined the guidescope tube from the Lowspec to the OAG, and now I can smoothly focus my guidecam...

Human: I'm building a custom focuser for my Explore Scientific 80ED using a cheap stepper motor and Arduino. The case is designed to be easily clipped on and off. All the necessary electronic components are listed on this GitHub page:...

This is a fine focuser based on the design from wal20, https://www.thingiverse.com/thing:3915702. It is designed to fit my vintage SMC Takumar 200mm prime lens that I use for astrophotography. ...The base adjuster is too finicky and this will help get...

After experimenting with a couple of existing designs, I encountered issues opening up the C-rings to accommodate my scope's unique shape, which led me to design a focuser that utilizes half-rings instead. Additionally, I was concerned that the...

After years of faithful service, my trusty focuser rubber seals finally gave out. Undeterred, I set out to create a drop-in replacement that would replicate the performance of the original with precision and accuracy. ... Key specifications include an...

This is a fine focuser based on the design from wal20, https://www.thingiverse.com/thing:3915702. It is designed to fit my vintage SMC Takumar 200mm prime lens that I use for astrophotography. ...The base adjuster is too finicky and this will help get...

This is a fine Focuser based on a design from wal20. It uses two #6-32 screws to tension and lock on a piece of steel plate. ...Beneath the ring are a piece of felt to ensure a good lock down.</p> <h3>Print instructions</h3><p>Printed on a Prusa Mk2,...

The original rubber knob can be placed again on the UpperGearHolder, and to disengage the motor for a rough first focusing, just pull out a bit the ServoSupport4Motor, focus using the knob and then release the motor support and the spring (or a...

The rack and pinion focuser of my original thing fixed the problem of rotating the camera during focus, but pushed the eyepiece way past the original location, which sometimes required collapsing the scope to get back into focusing range. This new...