graphics tablet mount 3d models

With the increasing prevalence of tablet-enabled devices, I decided to design and build a sturdy, straightforward bracket that can securely hold most 10-inch tablets with their covers attached. ...Additionally, I included a bottom hole specifically for...

I had my 8" Samsung tablet in the mount and it locked itself into place. ...Even after 2 hours of thrashing around Bathurst in the Ford V8 supercar, my actual wheel needs to be bigger to see the full screen, but I get the information I need, and the...

... and backward within an 8-inch range of motion. This design was initially created for my old HP 10 Tablet in the kitchen, where it's been working well so far, but could benefit from added support to prevent the tablet from wobbling when being used.

ASUS 7" tablet mount for 1.75" rollcage tubing, this project is currently being updated with a few improvements and I will be making some adjustments to the design in the near future. Update 3/12/17 - My prototype unit encountered a failure due to...

This wall mount was made for Samsung 10.1" Tablets. ...Other models may work too.<br/> As my printer was too small, I made 2 parts with a groove to glue it after it is printed.<br/> You will need a M6 screw, M6 nut and some washers to put it...

I decided to use additional parts that are more stable because the idea was that I needed a tablet mount for my Mavic Air as well as my DSLR. I already bought stuff, but it was way too bulky to transport. I needed a lightweight solution that I could...

... as instructed. Next, securely attach the Wall-Part to the Tablet-Part using strong adhesive strips like Tesa or 3M. Hang your tablet in its new spot, then thread the cable through the Bottom-Part and snap it firmly into place beneath the device.

My little ones finally have a dedicated area to recharge their tablets, keeping them organized and clutter-free is just one less thing I need to worry about.

... extra support. ... for this you have to print this part two times. Ich hab den " Tablet/Computer underdesk moun" von "OSXtraveller aufgeteilt zu einem, damit man es ohne extra stützen drucken kann. ... dafür muss man eben dieses teil 2x drucken.

The owner of an Audi Q2 recently purchased a tablet to enhance their driving experience. ...This individual opted for a 7-inch Samsung TAB4, which they secured with a custom-made tablet holder specifically designed for the Audi Q2's interior.

I opened the extremities in order to hold tablets of all sizes. ... I also removed the holes for hanging up with nails because I used strong double-sided tape This is a remix from https://www.thingiverse.com/thing:398515

I envisioned an elegant, slanted tablet cradle specifically tailored to the Lenovo 7" model. Its purpose was to seamlessly integrate these devices into a comprehensive home automation setup. ...The intricate design requires approximately 4.5 hours of...

made and designed a tablet holder that sits on the back of my hotas for gameglass in star citizen. ... Edit: October 15th 2020 For best results: Infill 20-25% Cura Tree supports (touching base plate) .2 resolution

This is a CD bay tablet holder designed specifically for a 7" tablet, and it fits my 7" Galaxy Tab perfectly in my 2007 Saturn Vue. I deliberately left the hole cutouts unfilled to accommodate various tablets on the market; simply use a Dremel or...

... your Nexus 7 to rest comfortably. You may need to sand down the alignment notches based on your printer's precision. Feel free to customize the dimensions of part 2 to fit other tablets. ...Don't worry about messy geometry - just enjoy the upgrade!

Remixed from a design on Thingiverse and modified to have a slightly shorter length to also accommodate vertical displays for small tablets.Print settingsLayer height: 0.20mmInfill: 20%No supports needed, print in the default orientation with longest...

I made this for my wife to be able to store her Cell and Tablet. She is pretty critical of my 3D printing but this passed her critical eye. It would be super convenient if your significant other shared the same name. ... Otherwise, feel free to remix...

This thing was designed so I could place my tablet in it and still use it at my desk. ...I have done a test print and fount that the upper supports were only one wall thick so I enlarged it to 2 or 3 walls thick.

cucu has a great model but it wouldn't fit on my print bed, so I remixed it. ...All I really did was remove ~50mm from the main body and added the same to the lower legs. Still fits tablets 165-265mm tall, but can be printed on a 180mm bed.

The adjustable grip of the Gamesir G3s's integrated phone holder can now accommodate smaller tablets, specifically those measuring 7" or 8" in size. The maximum width this extension will support is approximately 130mm. This design upgrade was...

Post-Printing: This tablet holder was printed in ABS with 30% rectilinear infill. Initially, I used 20% infill but the hook broke. To address this issue, I increased the infill to 30%. ...Additionally, acetone vapor smoothing will be applied to boost...

Also in the back, there's a carved channel to place an USB cable, once in place, just slide the tablet into the frame and since they're perfectly aligned the tablet plugs automatically to the USB plug when it gets totally inserted into the frame. ...2)...

My Version for an Adjustable and Printable Tablet Holder for the DJI Mavic Infill: Thirty Percent Four Bottom Layers and Four Top Layers are Required You Will Need: Two (Strong) Rubber Bands One Hex Screw, M4 x 30mm, Along with a Matching M4 Nut If...

I printed this thing: http://www.thingiverse.com/thing:440017, which is really nice, but I wanted to be able to turn the tablet further without hitting the swing arm. So I put the pieces in Tinkercad and sliced, diced, and glued them together to make...

Mandatory Components: * AUKEY Magnetic mount (44mm) - Available at Amazon: https://amzn.to/2Oyp1kE

To easily digitize a document, use a smartphone/tablet holder to take pictures at an adjustable height. Post-processing with CamScanner can correct color and distortion issues. ...Check out my design journey and failures in these blog posts: [Link...

... normally attached to front seats facing backwards. Remix also included remix from this file -> https://www.thingiverse.com/thing:2061636/remixes Fitting may be tight so may have to size up "car mount v3.stl" to 102% Used supports for "bar_1.0_180"

It uses a standard GoPro 1/4-20 tripod mount, but you could mount any number of small ballheads, etc on top of the post. Using a GoPro mount lends itself to using any number of device holders. Search here on Thingivers for "GoPro Tripod Mount" for...

So we needed a sturdy headrest mount that could withstand the punishment of our toddler's temper tantrums. We purchased 1 at "5 and below" for a Nintendo Switch but it didn't fit right. I used the base from that to hook it to the headrest. The...

Paying tribute to an outstanding mounting system I discovered during my expedition on Amazon, the Koala Mount 2.0 (http://a.co/d/7R21tyY) is a superior design boasting numerous impressive features. It relies on sturdy 3M Command strips or screws for...