gps mount for drone 3d models

for Lollipop 4 RHCP 5,8G (MMCX RED) & BN220 GPS PLA

for Lollipop 4 RHCP 5,8G (MMCX RED) & BN220 GPS PLA

for Lollipop 4 RHCP 5,8G (MMCX RED) & Matek Systems M8Q-5883 SAM-M8Q GPS PLA

It is also high enough so it doesn't touch the ground when the quadis flat. The T-style antennae can be mounted below the GPS holder with the stock TPU mount, or you can use the upwards-facing antennas in this mount (I must admit I just placed empty...

Thing I made to mount a Trackimo GPS tracker on the side of my Phantom 3 Professional Quadcopter. ... Trackimo-C is an updated version with a stronger mount

This is a suction cup camera mount for the A129 pro camera with GPS. It is designed to clamp around the GPS since I found sticking the GPS to a plastic paddle as if it were stuck to the windshield kills the GPS signal. It uses a tripod base with...

I just started using my phone as a GPS so I thought I'd use the same mount for my Garmin with out-of-date maps. This is a pretty specific adapter I made for my Garmin Nuvi 200 GPS mount. The adapter snaps into the same notches that the GPS unit has...

I picked up a budget-friendly GPS module from Banggood for just $11, but it proved to be a challenge due to its bulky size, which made it impossible to mount using standard accessories. In response, I rapidly designed a custom strap mount on SketchUp...

... a long range quad, a GPS may come in handy. ...Either as a fail safe or as a speedmeter. I couldn't find a mount for the front of the quad so I made one from scratch. There are two designs. ...One for the factory screws and one for flat top screws.

... a long range quad, a GPS may come in handy. ...Either as a fail safe or as a speedmeter. I couldn't find a mount for the front of the quad so I made one from scratch. There are two designs. ...One for the factory screws and one for flat top screws.

... in the part. I've been using a version of this for almost a year and it holds up great. Requires the mount clip that comes with any Wahoo. It might also work for Garmin with some slight modification, I think Garmin mount clips are flipped 90deg.

The Subject is a custom designed GPS Mount made specifically for the Full 3D Print Y6 Hexacopter Model. ... For this model, see the full product on: Flames - www.thingiverse.com/thing:1046175 Y6 hexa by Flames- www.thingiverse.com/thing:1001202

This provides a ball mount for a Garmin GPS, plus an HR Richter mount for a TST 507 TTPMS (Trailer Tire Pressure Monitoring Sensor), the whole thing goes into the slot in the front of the console of a 2020 RAM 2500/3500 truck that is intended to...

The CD slot mount features a 16mm ball and socket joint with a sphere. ...It works optimally with the swivel holder included in my portable Magellan GPS device. For printing, supports are required, at a resolution of .2, with an infill level of 50%.

This is a modified version of my earlier GPS BN220 mount, tailored specifically for a high-performance racing setup with an arm width of 11 millimeters. ... Edit 2022-03-10: The width of the cable recess has been expanded by 1 millimeter to accommodate...

This is an upgrade of the GPS Mount, found on http://www.thingiverse.com/thing:256474, that incorporates a 4mm cylinder. The rod stands at 7 cm tall and can be easily trimmed down to fit your desired length. I recommend leaving about 3/4 cm for...

... If you don't have one, consider purchasing the 3DPower 18x18mm M8N GPS + SMA Mount specifically designed for the Stynkebutt FK7 V4. This product can be found at taco-rc.com. ... To create this mount, use your 3D printer to print it in TPU material.

This thing is a holder for the V-900 GPS whichmight also fit the newer V-990 GPS datalogger. It's compatible with the GoPro mount or the Bontrager Blendr mount. The tab in the front fits into the USB port and locks into place. The hole in the back...

This device is a holder for the V-900 GPS which may also fit the newer V-990 GPS datalogger. It's compatible with the GoPro mount or the Bontrager Blendr mount. The tab in the front fits into the USB port and locks securely into place. The hole in...

The RMRC BN-180 GPS module is designed to sit directly on top of the F722-Wing Flight Controller, but it will also fit perfectly with the F405-Wing. * Update: As of May 20th, 2020 - The V3 version may be too short and pick up noise from the FC, so...

This mount is specifically designed for Garmin eTrex 10/20/30 series handheld GPS devices, but may also work with other Garmin models that use the same slide rails. The mount features a hinge for easy attachment and uses M3x25mm and M4x25mm bolts for...

I redesigned the GPS mount from SnappyFPV to use rigid material such as PLA instead of flexible TPU: I took out parts under the arm and three-quarters of the "roof", making it possible to insert the BN-220 without twisting the mount, although it...

uAvionix pingUSB: https://www.uavionix.com/products/pingusb/ http://rcubedengineering.com/ecommerce/pingefb.html Stratux Vk-162 Remote Mount USB GPS (remove the magnet under the decal):...

These are two variants of an antenna and GPS mount for iFlight Titan DC5 HD and similar frames for fpv copters with 21.6mm post distance. It is intended for the twin antennas of a DJI air unit that comes with it. The antenna orientation is a lot...

The result is a two-part model that prints easily together with epoxy to form a clip-on mount, allowing for a sleek and out-of-the-way installation while still providing clear visibility. A satisfying snap-in mechanism confirms the secure fit. ...Before...

I searched quickly for a GPS mount option in my 2017 Super Duty and came up with this little mount for the dashboard V area. It's mounted using double-sided tape, which proved to be a good choice. To get better print results, I split the model into...

Simple support for the N8M GPS module, to be assembled on the back side of the TBS source one frame, but it should also fit well on other frames with a 30 mm spacing between standoffs. It's suggested to print it in TPU, so the module stays in place...

Shark fin for installation on the frame series XL7. ...Designed for the installation of gps Radiolink TS100. ...Printed by ABS plastic with supports.

Many GPS and Phone mounts are designed for tubular handlebars. This simple adapter makes it possible to put these mounts on Clip On handlebars too. Print Settings: Printer: CraftBot Plus Rafts: Doesn't Matter Supports: No Resolution: .3mm Infill:...

I'm designing a surface-mounted accessory that lets you attach a 1-inch Ram Ball holder to your motorbike, perfect for securing GPS or phone devices. Since my bike features a flat aluminum dashboard, the bolts pass through from underneath and the...