goth modeling

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

I like you.text10 = ---textsizes = [13,13,13,13,8,8,8,10,6,10]Boat labeltext1 = Coast Guard Capacity Informationtext2 = ---text3 = Maximum persons|3text4 = Maximum gross load|100kgtext5 = Persons, motor & equip.|50 poundstext6 = Maximum...

Filament Dry Box (Peli Case) Storetwo standard 200mm filament spools in an air-tight Peli Case. Perfecting for storing your hygroscopic filaments after drying. The Dry box can be configured to simply store the filament, or by drilling and tapping 4 x...

Based on the given specification for generating an OpenSCAD script that will output a specific shape model made of acrylic plates, here's the script: ```OpenSCAD $fa=5; $fs=0.5; color("gray"){ translate([4,16,-24]){ mirror([1,0,0]) mirror([0,0,1])...

In Ultimaker Cura you first have to install the “Mesh Tools” extension which allows the “Split model into parts” action.Pneumatic tubes with outside diameter 3 mm are used. E.g. Festo PUN-H-3X0,5-NT. Locate the four holes in the housing and enlarge...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

You are free to share the model with attribution and please feel free to print it for someone in need but DO NOT CHARGE THEM MONEY. If you are not charitable enough to give a print of this away, then please don't waste your filament.</p> <p>I...

Your results in a bed mesh are probably better than these tests indicate.How do I get the code?There is a branch here on GitHub: https://github.com/garethky/klipper/tree/adc-endstopPlease should read the documentation.The config for the reference...

To connect this to the second hand holder disc, I bought a plastic tube of 1mm inner diameter from a modeling shop. I pinched one side a bit to make it flatter. This seems to work, but maybe I will have to glue it on the pin. I didn't do so yet...

There seem to be quite some error margin in production, if your model is a bit too big to fit, just sand off maybe .5 mm from the sides to make it fit.Completely(!) remove any filament remains inside the two enclosure parts.Fit servo into upper half...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

Update 220811:Added solid with 1deg step on requestReplace the code below to this, (BB and CC changed to 2 and 1 and replace STL to the new...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

Links Here are some useful and fun resources: - The Docs (SlimeVR Documentation) - Github Repository SlimeVR - Github Repository Hyperion - Thingiverse Hyperion (https://www.thingiverse.com/thing:5186756) - Cults3D Hyperion - CGTraders Hyperion...

If you do this, make sure to account for the thickness of these things to ensure that everything ends up flush as it should be. I've included a Sketchup model with more information, like joint lines, as compared to the .stl files. ...I will post more...

&nbsp;&nbsp;ENGLISH-------------Only tested on T12-X, but can work on equivalent models with boxes of the same dimensionsI found my T12-X soldering station a little too bulky, the screen not very visible and too dark. I also wanted to have all the...

A few copies of it will be printed, for two reasons: cooling during print and as spare if some print fails. raketplattform överdel_xy0.4mm_z0.2mm_ELIXIR_ELIXIR_ELIXIR_ELIXIR_ELIXIR.3mf raketplattform...

Another thing to note is that there have been a few minor changes to the model since I printed the one in the pic, however I don't think anything changed will cause a problem. The STP file is included for remixing. Just wanted to mention some info...

They should easily fit even on small printers; if you can print Hadley, you can print this mount.The mount uses a vinyl disk that sits on top of teflon pads, for very smooth motion.It is very lightweight, and can easily disassembled for compact...

You may need to adjust your switch's orientations in the holes depending on your model of keyboard switch, so be prepared to work through that. 13) Lay in the keyboard-switch-populated 3D-printed piece so that the pins face towards the inside of...

... There are also useful coat hangers and finger toys.Compliant mechanisms:In case you want to know more about compliant mechanisms, check out these models from BYU_CMR.

If you don't want to mess with a PLA support, you could probably print this part in two separate objects.I provide you the Fusion 360 file, so you can customize and change the model according to your rail system. I strongly recommend you to...

This is because it is a slide on design to limit the complexity of the model.&nbsp;&nbsp;INSTRUCTIONS:&nbsp;I tried my best to make this the simplest adjustable optic for nerf yet! As such it has only 3 parts that can easily be printed in under 2...

The design is made for an E12 bulb socket, but the "Bulb Holder Mount.stl" part could be easily modified in modeling software or simply by drilling new holes to line up with a bulb socket of your choosing. I am considering using an E12 smart bulb to...

Bear Exxa 1.0 is available here: https://www.thingiverse.com/thing:4362586 IMPORTANT: The Bear X axis will currently limit you to what alternative extruder/tool options you can mount without creating an adapter plate as it is different than previous...

Please check the images to see what it is included in this kit.This set contains: - Draconian Shock Troops (12)- Assault Dragons (4 + 4)- Commander Drakvarr- Flamagath Blackflame- Azgrathok - Chaos Dragonlord- Onixia the Tempest (Draconian Pinup)-...

Every link piece adds roughly 2,5 cm or 1 inch. Step eight:Cut Filament to 2,3 cm and attach the body strap to Piece K connector strap. Step nine:Cut again Filament to 2,3 cm and attach the N handles to M handle attachment:Congratulation, you just...

Happy soldering! Source Files This print was modelled in Onshape. You can access the source files from here:</p> <ul> <li><a...

The Hearst Tower, designed by Norman Foster, perfectly embodied the figure of the king with its massiveness and magnificent exterior.After determining the arrangement of the buildings, the next step was the creation of working models, which were...

 A lot of my models are designed for the 2.49mm walls that equate to 6 print lines with a 0.4mm nozzle.  Both the Tool Holders and the main Jig are setup to have a color transition at Z height. ... DonationsIf you found this print helpful, sending me a...