gopro shoulder mount 3d models
405668 3d models found related to gopro shoulder mount.
thingiverse
The following options were used in its creation: gopro_rod_nut_th = 3.6, gopro_bar_screw_shoulder_th = 6, gopro_bar_rod_d = 33, gopro_captive_protruding_h = 0.5, gopro_bar_screw_nut_d = 8.2, gopro_captive_rod_angle = 45, gopro_captive_rod_id = 3.8,...
thingiverse
Instructions Using the Following Options: * gopro_captive_rod_angle: 45 degrees * gopro_bar_screw_head_diameter: 6.2 millimeters * gopro_captive_protruding_height: 0.5 millimeters * gopro_bar_screw_nut_diameter: 6.01 millimeters *...
thingiverse
To assemble it, utilize the following specifications: gopro_secondary_rotated = 1; gopro_bar_screw_shoulder_th = 4.5; gopro_rod_nut_od = 8.05; gopro_captive_protruding_h = 0.5; gopro_bar_screw_head_d = 6.2; gopro_rod_nut_th = 3.6;...
thingiverse
www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions: Using the Following Options: gopro_rod_nut_od: 8.05 gopro_ext_len: 20.7 gopro_bar_screw_d: 3 gopro_captive_rod_angle: 45 gopro_ext_th: 3 gopro_bar_th: 3.2 gopro_secondary_what:...
thingiverse
Below are the specifications used for this particular design: - GoPro captive rod diameter: 3.8mm - GoPro rod nut thread diameter: 3.6mm - GoPro bar diameter: 3.2mm - GoPro rod nut outer diameter: 8.05cm - GoPro bar screw diameter: 3mm - Extended...
pinshape
Key Features: * Gopro Bar Gap: 2.4 mm * Gopro Bar Screw Nut Diameter: 6.01 mm * Gopro Extension Length: 50 mm * Primary Mount Type: Triple * Secondary Mount Type: Clamp * Gopro Rod Nut Outer Diameter: 8.05 mm * Gopro Captive Rod Inner Diameter: 3.8...
thingiverse
The design includes the following specifications: gopro_rod_nut_th = 3.6, gopro_bar_rod_d = 27.5, gopro_secondary_rotated = 1, gopro_captive_rod_id = 3.8, gopro_ext_th = 3, gopro_bar_screw_d = 3.1, gopro_bar_screw_nut_d = 6.01,...
thingiverse
A remake of the expensive GoPro bite mount or mouth mount for the actions sports where hands must be free. I use it for surfing. Print with support and be sure to remove completely the support between the 3 holes or the GoPro will not fit precisely....
thingiverse
The options used to create this mount include gopro_rod_nut_th = 3.6, gopro_secondary_what = clamp, gopro_secondary_rotated = 0, gopro_bar_screw_head_d = 6.2, gopro_rod_nut_od = 8.05, gopro_bar_th = 3.2, gopro_ext_th = 3, gopro_captive_protruding_h =...
thingiverse
My specifications include a triple primary setup, a 4.5mm gopro_bar_screw_shoulder_th, and a 0-degree gopro_secondary_rotated angle. The mount features a clamp for the secondary GoPro attachment and a 20.7mm gopro_ext_len. ...It also includes an 8.05mm...