gopro screws 3d models

Modified from Terry Tumulty design to only use M5 screws. ...Original design: GoPro Tube and Pipe Mounts-Adapter to rotate camera 90 degrees-Extension arm-33.4 mm 1.315 ID clamp mount (works well with 32 mm plumbing pipes)

Customized version of https://www.thingiverse.com/thing:3723982 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3723982

Customized version of https://www.thingiverse.com/thing:3723982 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3723982

Customized version of https://www.thingiverse.com/thing:3723982 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3723982

Customized version of https://www.thingiverse.com/thing:3723982 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3723982

Low Profile thumb screw can be used for a GoPro camera mount, or use the same screw on a Keihin Carburetor for the idle adjustment. Brass screws are better for the carburetor, the screw thread is M5. ...Can be printed small side down without supports,...

Low Profile thumb screw can be used for a GoPro camera mount, or use the same screw on a Keihin Carburetor for the idle adjustment. Brass screws are better for the carburetor, the screw thread is M5. Can be printed small side down without supports,...

......I printed a prototype but faced an issue; however, the speed range tested was between 80-90 km/h. To ensure safety, use a security cable, which is highly recommended. Simply attach your camera using the 1/4 screw and secure it with the GoPro bracket.

I made this mount to be able to screw my Chinese GoPro knockoff into the hans device holes on my helmet (Zamp FSA-3 with M6 holes). This could easily be used to mount onto other things as well though. ... Align so that M6 hole lies flat on bed and 3...

This is a simple straight element compatible with the GoPro mounting system. ...It measures 50 mm from axle to axle. ​The mount uses a standard GoPro interface so can mount to a whole hose of items.

This is a simple straight element compatible with the GoPro mounting system. ...It measures 50 mm from axle to axle. ​The mount uses a standard GoPro interface so can mount to a whole hose of items.

I re-ran Remix 2783514 through Netfabb to resolve the issue with Slic3r. ...The file now opens and prints flawlessly.

This is a personalized rendition of http://www.thingiverse.com/thing:278871, created using the Customizer tool (http://www.thingiverse.com/apps/customizer/run?thing_id=278871). ...The specifications followed were a tolerance level of 0.3 and a length...

You can use Blender to personalize the mount with a name or do whatever you need to do with it.

Remixed from Fab_ster incredible design, this is a RED Komodo 6k dummy with 1 BP-975 at the back and a 45x5mm thread lens hole that allows you to screw on some stuff like a gopro Hero 8 attachment or a lens dummy to add weight. Makes it perfect for...

GoPro Hero 4/5 Session users can now transport their gear with confidence, thanks to the tough new rugged storage/transportation case featuring a secure screw-on lid. ...This innovative case boasts four dedicated SD and four micro SD card slots for...

I designed and built my own adapter since all the others needed a threaded insert, so I added the necessary threads to it. ... The adapter prints flawlessly using a 0.4mm nozzle.

... Note: I used a 2 inch long 1/4 inch screw and a second nut to hold the tripod accessory for my GoPro firmly in place. You can do without the second nut and still get a firm mount if you position the screw at the right orientation for your mount.

https://thangs.com/Solidware/JR-Module-Bay-ExpressLRS-No-Screws-No-Supports-16442 I use my t-lite for flying a Tello too, and I made phone holder arm out of gopro mount parts. This design is to mount the Micro size ES24TX from Happymodel to t-lite or...

Rotorama Spectre - GoPro Hero 6/7 Mount (Lightweight) for Screws: A Sleek and Robust Solution The Rotorama Spectre is a cutting-edge, lightweight mount designed specifically for the GoPro Hero 6/7 series. This innovative holder boasts an optimal hole...

https://thangs.com/Solidware/JR-Module-Bay-ExpressLRS-No-Screws-No-Supports-16442 I use my t-lite for flying a Tello too, and I made phone holder arm out of gopro mount parts. This design is to mount the Micro size ES24TX from Happymodel to t-lite or...

To print a 30mm M5 bolt with a hexagonal head, totaling 33.5mm in length, refer to PDF revision 00. This part fits existing mounts and an upcoming design. It was created using Autodesk Inventor 13 and digital calipers. Print with PLA on a Replicator...

... were perfect in version 1.2. Version 1.3 includes a standing variation that may improve stability further. Simply print with solid infill to utilize this mount. Requirements include a GoPro camera, two screws, and a screwdriver for assembly.

By popular demand, this is a version without battery of my Komodo dummy (available with battery here https://www.thingiverse.com/thing:4655431) Remixed from Fab_ster incredible design (https://www.thingiverse.com/thing:4147456), this is a RED Komodo...

Cut a 1/4 inch thread.

You require one M5 by 40mm long bolt, a single piece.

Tpu Flex GoPro HERO 4 case frame mount 1/4 screw tripod

Work in progress - Just getting started with MeshMixer. I remixed this so I could use GoPro8 with TBS ND. It looks like Fincky uses a large ND filter I'm not familiar with in his design, so wanted something more snug for my TBS ND. Print w TPU,...

Work in progress - Just getting started with MeshMixer. I remixed this so I could use GoPro8 with TBS ND. It looks like Fincky uses a large ND filter I'm not familiar with in his design, so wanted something more snug for my TBS ND. Print w TPU, 40%...

... orientation. ...File List: GoPro_QR_stand.scad - OpenSCAD source code for tweaking parameters; GoPro_QR_stand.stl - printed version; tv-335179_GoPro_Flat_Mount_with_screws.stl - original file from Thing 335179, necessary for creating a custom version.