gopro roll cage mount 41mm tube 3d models
481132 3d models found related to gopro roll cage mount 41mm tube.thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_secondary_rotated = 1 gopro_captive_protruding_h = 0.5 gopro_rod_nut_od = 8.05 gopro_bar_screw_head_d = 6.2 gopro_bar_gap = 5 gopro_ext_len...
thingiverse
Customized version of http://www.thingiverse.com/thing:909819 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=909819
thingiverse
A Gopro mount that fits on a 41mm diameter roll cage tube (Porsche 996 GT3 mk1 Clubsport)
thingiverse
Customized version of https://www.thingiverse.com/thing:62800 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=62800
thingiverse
Customized version of https://www.thingiverse.com/thing:62800 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=62800
thingiverse
Customized version of https://www.thingiverse.com/thing:62800 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=62800
thingiverse
Customized version of https://www.thingiverse.com/thing:62800 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=62800
grabcad
This is a GoPro mount for a 43 mm tube, so it fits on most roll bars. ...Changing the diameter shouldn't be too hard just cut extrude a larger hole.
thingiverse
Please select an option for the following parameters and provide measurements accordingly: • gopro bar screw diameter = __mm • gopro bar thickness = __mm • angle between captive rods = __deg • secondary rod feature type = • Clamp or hinge? ... = •...
thingiverse
Gopro mount for 38mm rollcage tube You also need https://www.thingiverse.com/thing:2732044 (gopro_cage_mount_GOPRO)
thingiverse
Motorcycle fork mount for gopro. ... Designed for M4 nuts and bolts.
thingiverse
gopro_cage_mount_CAGE.stl Is the Part connected to the Cage gopro_cage_mount_GOPRO.stl is the GoPro mount. Just separated the parts. ... Everything else -> https://www.thingiverse.com/thing:44997
thingiverse
A friend needed to mount his dash pod to his roll cage. This little clip/mount does the job rather well. ... Fixing hole is 6mm
thingiverse
An alternative to GoPro's roll bar mount, this design solves problems like large posts and limited flexibility for angled bars. It uses zip ties for secure attachment and incorporates a swivel for skewed angles. Suitable for 1.75 inch tubes, minor...
thingiverse
After suffering a number of failures of "Roll Cage Swivel Mount for GoPro" (https://www.thingiverse.com/thing:44997), I designed a MUCH STRONGER version with the same functionality, but with two key improvements. 1) The new base component is longer...
thingiverse
https://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_captive_protruding_h = 0.5 gopro_bar_screw_nut_d = 9 gopro_ext_len = 35 gopro_bar_rod_d = 42 gopro_captive_rod_angle = 45 gopro_bar_screw_d...
thingiverse
The most effective GoPro installation spot inside a vehicle is often on the diagonal rod extending from the B-pillar support. A straightforward OpenSCAD blueprint for this 1.75" bar diameter at a 45-degree angle to the horizontal plane has been...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_ext_len = 30 gopro_bar_screw_nut_d = 6.01 gopro_bar_screw_d = 3 gopro_rod_nut_th = 3.6 gopro_bar_th = 3.2 gopro_bar_screw_head_d = 6.2...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_captive_rod_id = 3.8 gopro_bar_th = 3.2 gopro_bar_screw_d = 3 gopro_rod_nut_od = 8.05 gopro_bar_gap = 2.4 gopro_bar_screw_nut_d = 6.01...
thingiverse
Simple GoPro mount for racecar cages or tubes with 50mm diameter (+-10mm) You will need: 2x M5x30 or 2x GoPro Screw 3x M5 nut Optional: Glue 1-2mm rubber sheet on insides for better grip (like in photo)
thingiverse
Mount Ram ball to fit 1.75" UTV rollcage securely using a 1" ball mount.\n\nTo secure your mounting setup, refer to the instructions below.\nFitment Notes:\nThe top side holes are tapped for 1/4" bolts with washers and nuts for maximum support.\nThe...
thingiverse
Designed to clamp around 44.4mm ROPT510 tubing, sized up slightly to allow a wrap of electrical tape to prevent it from slipping and protect the powder coat on my roll bar.
thingiverse
Basically just a 41mm Daybreak cage for the Regulator/Hyperfire that looks a little nicer and has improved dart entry. This has not been tested (8/24/2019). Just based off what fits in the Regulator shell. Should work in Hyperfire. ...Feel free to test...
thingiverse
Made an adapter to attach a bottle cage mount to a GoPro buckle. I originally designed it to carry my speaker on my surfboard using a bicycle bottle cage. ... Hardware: 5mm nut and bolt
thingiverse
I just wanted some design practice and I knew someone wanting to build a Jyn Erso, so I thought I'd make up a 41 mm cage since I didn't see one. I believe it is daybreak compatible, as you can see I opened up the flywheel surrounding to account for...
thingiverse
It mounts to a 1.75" roll bar. It fills an under served category, bar mounted, around the cloth hood, and above the windshield. I would recommend printing with ASA UV resistant plastic, or coating your plastic with paint or epoxy. In PLA, it...
thingiverse
The specifications used for this model include a gopro_captive_rod_id of 3.8mm, gopro_rod_nut_th of 3.6mm, gopro_bar_th of 3.2mm, gopro_rod_nut_od of 8.05cm, gopro_bar_screw_d of 5.4cm, gopro_ext_len of 20.7cm, gopro_bar_screw_shoulder_th of 4.5mm,...