gopro hero 8 battery case

Luban Stool (parameterized & print-in-place with tape)
prusaprinters

The corner fillets stopped all 8 outside corners lifting for me. Leg StandoffsTo trick the slicer into giving me pretty top and bottom layers for all the parts, I needed a way to keep the legs separate while they were sitting on top of other...

Spooky Scary Skeleton Robot
prusaprinters

The Servo moves a mechanism inside to raise the eye brows and lower the jaw.BILL OF MATERIALSPartDescriptionQtyCostRaspberry Pi PicoThe $4 microcontroller from Raspberry Pi1£4.00ServoA low cost SG90 Servo1£3.00Ultrasonic Range FinderHC-SR04 3.3v...

EmoThingiverse
thingiverse

0x 0x, soy 7- 3 2 06, and that is a little bit 01 0x 0x 0x 0x, and 2 0x 0x, and the same goes to 0x 8 019. ...And <|im_start|> 0x<|im_start|> 0x<|im_start|> 3<|im_start|> 0x<|im_start|> 0x0<|im_start|> 0x<|im_start|> 0x<|im_start|> 0x<|im_start|>...

Mechanical wall clock
prusaprinters

If there is significant resistance, make sure the tolerances are correct, that there are no imperfections in the print causing resistance and that both the shaft and gear are properly...

Prusadusa and the sands of time clock
prusaprinters

Test early, test often!1.Start by pushing all the bearings into the gears, depending on the accuracy of your printer you might need to use a pumpwrench or pliers to get the bearings to fit. 2.Push the drive_gear_motor_side onto the shaft of the...

VAG EGR VALVE 03G 131 501 REPLACEMENT GEARS
pinshape

8. **VW PASSAT CC** - 2.0 BlueTDI 105 horsepower: Introduced in 2009 for the Passat CC. - 2.0 TDI 103 horsepower: This engine variant was part of the standard Passat CC range from 2008 onwards. - 2.0 TDI 125 horsepower: A higher-power...

S22 3PO: The 3D Printed Option: KingSong S22 Suspension Slider FIX: Bearing Rollers
prusaprinters

No warping!Print the cap STL:4x left4x mirrored (for right side)Print settings:3 walls100% infillPrint the wheelsChoose the right wheel size! There's 6 different STL files, each with different outside diameters:+0.0 → 18.42diam+0.2 → 18.62diam...

3D Marble-Maze
prusaprinters

If your slicer adds more supports force him with support blockerColor: Accent color1Obstacle 7Layer-Height: 0.2 mmInfill: 15%Supports: Yes (on build plate only)Color: Accent color1Obstacle 8Layer-Height: 0.2 mmInfill: 15%Supports: NoColor: Base...

Puzzle box 1
prusaprinters

It may be a tight fit so take it slowly so the lid does not break.Place the Chamber lid into the Chamber and turn it. This is meant to be tight (which is why the screws should have 7mm heads) so if needed you can use the Shell as a...

Bre In Space! MakerBot Mars Base.
thingiverse

My brave Bre the makernaut {8} has a ball and socket joint that is printed already assembled. No human assembly is required and it is impossible to disassemble this ball and socket joint. Not only that, this printed ball and socket joint can hold its...

Lap camera gia re
prusaprinters

Đầu ghi 4, 8,16, 32, 64 cổng. Đầu ghi tường thích với các dòng camera 2k, 4k hoặc công nghệ analog hay IP.</p><p>2. Camera quan sát<br>Camera quan sát là một phần quan trọng nhất trong hệ thống camera quan sát hoàn chỉnh. Tùy theo yêu cầu khách hàng,...

Sandro
thingiverse

http://www.thingiverse.com/apps/customizer/run?thing_id=287025\n\n \n \n Instructions\nUsing the following options:\npixel_size = 1.8\nthickness = 1.0\npanel_shape = 3\ngrid_size = 0.2\npicture =...