gopro bar mount 3d models

RC Car SCY 16103 Jeep Gantry 1:16 - Hook mountTrailer tow bar for RC car can be downloaded here:https://www.printables.com/cs/model/265816-trailer-tow-bar

https://www.thingiverse.com/apps/customizer/run?thing_id=62800 Using these settings: GoPro Bar Rod Diameter: 31mm Primary Mount: Triple Configuration Secondary Attachment: Clamp Type Bar Screw Hole Outside Diameter: 8.05mm Bar Screw Head Diameter:...

... as well. Uses stock hardware to mount.You'll need:GoPro capture nut1 x M5 x 20mm2 x M3 x 10mm socket/cap bolts to secure the insertYou'll need supports on just the edges of the GoPro holder to make sure the nut and bolt hole come out well.

Took the Blue Yeti VIVO mount by DeepfriedchriL and cut off the hinge to just leave a bar that mounts to a 35 mm bar monitor mount. ...Made it so that I could clip my Samson Go Mic onto above my monitor.

This is a GoPro mount for a 43 mm tube, so it fits on most roll bars. ...Changing the diameter shouldn't be too hard just cut extrude a larger hole.

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_gap = 2.4 gopro_rod_nut_od = 8.05 gopro_ext_th = 3 gopro_bar_screw_d = 3 gopro_bar_screw_head_d = 6.2 gopro_rod_nut_th = 3.6...

Amazon Sound Bar Speaker Mount secures tightly to Amazon sound bar base, replacing traditional rubber feet with sturdy metal screw attachment. Simply tighten securely into pre-drilled holes on Amazon sound bar housing, ensuring a stable and level...

This is Insta360 Go3 mount compatible with Gopro mounts.

Simple phone holder that can be mounted to GoPro mount

Mount for the Sofirn HS41 headlamp for GoPro mount

Print 2x base holders, 2x Bar holders and mount over 2 studs at 16.5 inches outside to outside so the base will fit snug on its holders. You'll have to get creative for the wall hooks; I chose to superglue them to a trim bar that's screwed into the...

Here are the specifications used for customization: gopro_bar_screw_shoulder_th = 4.5, gopro_ext_th = 3, gopro_secondary_rotated = 0, gopro_primary = example, gopro_rod_nut_od = 8.05, gopro_ext_len = 50, gopro_bar_th = 4, gopro_bar_screw_nut_d =...

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_screw_nut_d = 6.01 gopro_bar_gap = 2.4 gopro_ext_len = 50 gopro_secondary_what = triple gopro_captive_protruding_h = 0.5 gopro_primary =...

Using the following options: gopro_rod_nut_od is set to 8.05 gopro_ext_th is adjusted to 3 gopro_ext_len remains unchanged at 0 gopro_bar_screw_d has been set to 3 gopro_captive_rod_angle is precisely calibrated to 21 gopro_bar_th stands firmly at 3...

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following settings: Gopro Extension Thread Diameter: 3 mm Gopro Bar Rod Diameter: 25 mm Gopro Captive Protruding Height: 0.5 mm Gopro Secondary Rotated: No Gopro Rod...

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following settings: gopro_secondary_rotated 1 gopro_captive_protruding_h 0.5 gopro_ext_th 6 gopro_bar_screw_head_d 7.2 gopro_rod_nut_od 8.05 gopro_bar_screw_d 4...

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_screw_nut_d = 6.01 gopro_bar_gap = 2.4 gopro_ext_len = 100 gopro_secondary_what = triple gopro_captive_protruding_h = 0.5 gopro_primary...

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: Gopro Bar Screw Head D: 6.2 Gopro Captive Rod Angle: 45 Gopro Secondary Rotated: On Gopro Bar Gap: 2.4 Gopro Bar Screw Nut D: 6.01 Gopro Rod Nut...

Instructions Using the following options: gopro_captive_protruding_h = 0.5 gopro_rod_nut_th = 3.6 gopro_captive_rod_angle = 45 gopro_ext_th = 3 gopro_secondary_rotated = 0 gopro_bar_screw_head_d = 6.2 gopro_bar_th = 3.2 gopro_secondary_what = clamp...

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_captive_rod_id = 3.8 mm gopro_bar_th = 3.2 mm gopro_secondary_rotated = 0 degrees gopro_bar_screw_nut_d = 6.01 mm gopro_bar_screw_d = 3 mm...

https://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following settings: gopro_bar_gap = 2.4 gopro_captive_rod_id = 3.8 gopro_bar_screw_head_d = 6.2 gopro_captive_protruding_h = 0.5 gopro_bar_screw_shoulder_th = 4.5...

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_ext_len = 20.7 gopro_bar_th = 3.2 gopro_captive_rod_id = 3.8 gopro_bar_screw_d = 4 gopro_bar_screw_nut_d = 6.01 gopro_bar_gap = 3...

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_captive_rod_id = 3.8 gopro_secondary_rotated = 0 gopro_primary = triple gopro_ext_len = 0 gopro_bar_rod_d = 31 gopro_bar_screw_head_d = 6.2...

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_ext_th = 3 gopro_bar_th = 3.2 gopro_captive_rod_id = 3.8 gopro_bar_screw_head_d = 6.2 gopro_ext_len = 21 gopro_captive_rod_angle = 45...

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_rod_d = 25 gopro_secondary_what = clamp gopro_primary = double gopro_rod_nut_od = 8.05 gopro_bar_screw_head_d = 7.2...

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_rod_nut_th = 3.6 gopro_ext_th = 3 gopro_captive_protruding_h = 0.5 gopro_secondary_what = double gopro_bar_rod_d = 31 gopro_primary = triple...

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_screw_d = 3 gopro_rod_nut_th = 3.6 gopro_secondary_what = rod gopro_captive_rod_id = 3.8 gopro_bar_th = 3.2 gopro_primary = double...

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Use these options: Gopro bar thickness: 3.2 Gopro primary: Triple Gopro external thickness: 3 Gopro captive rod diameter: 3.8 Gopro bar rod diameter: 12.8 Gopro bar screw...

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 **Instructions** Using the following settings: Gopro Bar Screw Shoulder Thickness = 4.5 Gopro Secondary Option = Double Gopro Bar Screw Diameter = 3mm Gopro Rod Nut Thickness = 3.6mm Gopro...

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_secondary_rotated = 0 gopro_ext_len = 200 gopro_captive_rod_id = 3.8 gopro_bar_th = 3.2 gopro_primary = triple gopro_bar_screw_head_d = 6.2...