gopro 90 degree mount 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: primary_rods_gopro_bar_gap = 3 primary_rod_captive_angle = 45 primary_captive_rod_id = 3.8 gopro_mainbar_length_diameter = 25 gopro_triplets_count...

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_secondary_what = clamp gopro_rod_nut_od = 8.05 gopro_bar_screw_d = 3 gopro_bar_rod_d = 20 gopro_captive_rod_id = 3.8 gopro_ext_th = 3...

Gopro Hero 8 Mount for Floss 3 I've got GoPro Hero 8 mounts for other frames as well, please check uploaded other stuff.

Gopro Hero 8 Mount for Armattan Marmotte I've got GoPro Hero 8 mounts for other frames as well, please check uploaded other stuff.

25mm cable 90 degree panel mount for Spot welding machine two cables which goes from spot welding machine to welding pen

55 degree mount for HD-Zeron 90 fps camera Version 16 has updated tabs around camera to help protect it better

this is a mount to turn your touchscreen/control 90 degrees. works well when printer is sideways on a stand. ...moved one mounting hole may need drilled slightly to fit.

This is a 90 degree action camera mount connector which I made for using my insta360 X3 camera (with waterproof case) on my Citymate sea scooter Print as is, no support or brim required. ... Infill 20% recommended

Based on thingiverse's #369891 design, this custom mounting solution offers a distinctive 90-degree configuration that seamlessly aligns with the designated slot on the K8200's right support beam.

I have a range of GoPro Hero 8 mounts that fit the Armattan Marmotte, plus others for various frames - be sure to take a look at my uploaded content.

This adapter mounts your Ender 3 spool holder at a 90-degree angle to the lower-front frame, with the spool parallel to the frame. This is useful if you've installed a direct drive extruder and redirected the filament path to the front of the z-axis...

Mount your Rode Wireless Go receiver 90 degrees in the shoe mount so you can see the little screen. Slide your Wireless Go up from the bottom and then pop it in your camera's shoe mount. I made this carefully to get it to print without supports.

Mount the Rode Wireless Go receiver 90 degrees into the shoe mount so you can view the small screen clearly. Position your Wireless Go by sliding it upwards from the bottom, then firmly insert it into your camera's shoe mount. After countless...

A quick mount adapter to turn one of the side bins 90 degrees on my Dillon 550 with Inline Fabrication side bins. I find it easier to load cases when the bin is facing me rather than sideways like the output bin. ...

It's just a mount thingy that turns filament spool 90 degrees and hopefully prevents oscillation of the spool while printing and improves overall quality of a print. To assemble this thing you'll need: four M5x16 round head cup screws, two M5 nuts...

SMA mount for marmotte (90 degree antenna/adapter) Based on WickedWingman design which is perfect for straight antennas. Edit: 2. version added which has a counterbored part for the pigtail flange. This will prevent the pigtail from spinning. ...

Based on http://www.thingiverse.com/thing:369891, this mount has a 90 degree angle, so that it fits on the right upright on the K8200. Category: 3D Printer Parts

This mount has a 90-degree mounting angle, making it possible to use the Belted Extruder v4 1.75mm with bowden tubes going horizontal over the xBot 3D Printer. In case you have a left 8mm rod which protrudes a bit, you can use the model Clip-On 90c -...

I've got a bunch of GoPro Hero 8 mounts that fit perfectly on the Floss 3 frame, and I've even uploaded some of them to share with you! ...Check out my other uploaded goodies, too - they're all compatible with the Hero 8.

This is a versatile 90-degree mount for Modern Robotics sensors, designed to bring a color sensor closer to the floor with ease. It's an ideal piece for out-of-the-way attachment points that require precise positioning. ... - Team 8417 Print Settings:...

... Angled at 90 degrees for forward-facing unit placement.\r\n5. Recessed screw holes ensure Eufy mounting bracket fits flush against adapter.\r\n6. ...Slightly offset design tucks Eufy doorbell closer to door jam, providing more free space in doorway.

... your extruder doesn't have mounting holes. This mount also blocks less of the fan output than mounting it to the extruder block. This mount also includes traps for m3 nuts. ...It works great with the J-head, and should work with the Magma as well.

The revised design now features 90-degree adjustable antenna mounts with precision-drilled tube holes. This upgrade enables users to securely fasten antennas in place using two 10mm screws, ensuring a snug fit and minimizing wobbling. Future...

This spool holder mount adapter will allow your Ender 3 (and possibly other Creality models) spool holder to be mounted on the lower-front frame at a 90 degree angle so that the spool is parallel to the frame. This is useful if you've installed a...

This fan mount is ideal for extruders without mounting holes. It attaches to the carriage and allows more fan output than when mounted on the extruder block. Additionally, it features built-in M3 nut traps. First, print the mount, then install two M3...

This is a 90-degree mount for the filler spool holder. It holds the filament spool so that it is "facing" the wall, or I guess rolling toward or away from the wall. I needed this as I like to mount my spools either in front or behind the printers...

I'm excited to share my TBS-style SMA mount at 90 degrees without any antenna tubes. I personally printed it, and I must admit that I wasn't thrilled with the shortness of the SMA plug. The thickness of the 3D part hole is 1.5mm - anything greater...

Remixed and angled 90 degrees toward front and lowered to get better angle from the corner of the printer. Print with supports, PLA is fine.

This is a 90-degree mount for the filler spool holder. It holds the filament spool so that it is "facing" the wall, or I guess rolling toward or away from the wall. I needed this as I like to mount my spools either in front or behind the printers...

This is a bespoke 90-degree battery holder specifically designed for the Fullspeedrc Toothpick, requiring a 2mm screw and nut for secure installation. Engineered to accommodate Tattu 2s 450mah batteries with precision fitment. Weighing in at just...