google nest hub under cabinet mount 3d models

Default Dimensions: 3.7 cm wide, 10.5 cm long (3.5 cm of which is the mounting plate) 2 counterbore screw holes: Intended for #6 (3.5mm wide) screws with under 8mm wide heads. 4mm deep counterbore into 7mm thick mounting-plate. Remixed to: * Add a...

As described. ... Fitted to my Diamond X Collection bathroom cabinet. Just print 1 & 2. ...All goes together nicely as interfaces clearanced.

The under-desk headphone holder is rotating.

Designed up this Under desk headphone mount which can be either screwed or double-tapped under the desk. This can be printed in 3 types Type 1 - One solid body, (Support Required) Type 2 - Is split into 2 halves, print 2 numbers and join then the...

I built a straightforward hook mount that attaches under my desk, making it effortless to stash my laptop out of sight yet still within easy reach. To secure it in place, I applied a strong bond using 5-minute epoxy directly to the desktop underside....

The original creator remixed an existing under-desk mount to give it a lighter feel. By making this change, they managed to reduce filament consumption by about one-third even after adding a stabilization block that helps keep things stable. They...

This is a simple clamp mount that can hold your headphones under your desk when you don't need them. There are two frames. One for headphones with a headband width of up to 35mm and one for a width of up to 45mm. Maximum Desk thickness: 65mm ...

Designed this simple and universal under desk mount after noticing a lack of premade alternatives. The "male" part must be glued to the thing you're mounting and the "female" part can be screwed to the underside of a desk. The hole in the middle can...

By placing it under the edge of my desk, I was able to keep my workspace clutter-free while still having easy access to the volume control or being able to switch to using speakers. This design uses the factory screw locations on top for the case...

I Needed some extra space in my cabinet so I crafted some coffee cup hangers to hold my mugs underneath my cabinets. They function perfectly! The initial design I had used a more prominent hook, but it made it difficult to attach them with a...

Bed mouted table for beds with a 2,5 cm gap.(Reccomended to place a small piece of cardboard in between, as it is not that tight.)For the Nest Hub holder i glued the pieces together with a hot glue gun.  My print settings:Infill: 20%Layer height: 0,2...

I decided I'd rather have more desk space so I designed some brackets to be able to mount the laptop under my desk(sit/stand). I made sure to leave some open space in the bracket for my power supply. ... I also made sure to have holes so you can get a...

This mounting bracket is designed for a high-power LED lighting board (http://www.thingiverse.com/thing:27550) which can be placed under cupboards to illuminate countertops. To assemble, print the bracket and install the LED board using #6 wood...

Inspired by gpvillamil's design on http://www.thingiverse.com/thing:1370241, I crafted a mount that keeps the eero in its default orientation while suspending it under a desk. Note that the material beneath your desk may cause interference issues.

Inspired by http://www.thingiverse.com/thing:1370241 by gpvillamil, I designed a mount to keep the eero's default orientation but suspend it from under a desk. Note that the material in your desk may cause interference. The eero blog says "Keep your...

Designed this simple and universal under desk mount after noticing a lack of premade alternatives. The "male" part must be glued to the thing you're mounting and the "female" part can be screwed to the underside of a desk. The hole in the middle can...

One cabinet boasts a 135-degree angled corner, while the other has a standard 90-degree corner. The recess for the magnets in the part measures .737 inches in diameter. Here are the specific magnets I employed: Neodymium Disc Magnets (07047) with...

... of other cutting-edge formats. ...The native file type remains .skp, while the 3ds Max scene utilizes 2016 version capabilities, precisely rendered using Vray 3.00's latest features. Kitchen cabinets in this rendering demonstrate outstanding detail.

One screw velcro mount for cable management

Designed this simple and universal under desk mount after noticing a lack of premade alternatives. The "male" part must be glued to the thing you're mounting and the "female" part can be screwed to the underside of a desk. The hole in the middle can...

Under desk mount for rollo thermal printer. Found a few online that looked nice, but I didn't want to spend the money knowing I could make a version on my own although it would have been faster and technically cheaper :D This model is one piece so...

Inspired by http://www.thingiverse.com/thing:1370241 by gpvillamil, I designed a mount to keep the eero's default orientation but suspend it from under a desk. Note that the material in your desk may cause interference. ...The eero blog says "Keep your...

Designed this cable tidy as our thermostat is quite close to the plug socket so we have a lot of unsightly cable on the kitchen counter. Printing: Print in PLA mines in vanilla white but signal white would look better. The hole should be big...

<p>Had problem with rain on the doorbell so i designed a simple model to protect it from the rain. It don't cover any view from the camera. ...It has a hole in the top so its easy to remove the doorbell when its time to charge the battery.&nbsp;</p>

Mushroom stem for the Home Mini to make it look like a mushroom. Two piece base and top that do not need supports to print. Print stem standing and top flat. I did not need to glue mine together, but it depends on the accuracy of your printer. ...

didn't want the same old snorlax that I've seen across the internet so I made something new.. ...I added a v2 with a stand built in since my original version wasn't super stable

Remix of the stand created by CerberusNOR. But this version does not require a screw. ...Just put the pin in the hole until the back is alligned; you could add some glue if it will pop out; but mine works fine without.

Had problem with rain on the doorbell so i designed a simple model to protect it from the rain. It don't cover any view from the camera. ...It has a hole in the top so its easy to remove the doorbell when its time to charge the battery.

Needed to increase the angle of the doorbell camera. Two attempts to find the correct angle, one at 25 deg, second at 30 deg. Standard wedge that comes with the bracket is 20 deg. Enjoy! 3D CAD file attached for modeling purposes, if you need...

Rails for hanging IKEA or smart store boxes under shelves etc Three different types. ... Fits many different types of storage boxes