golf club for oculus quest 2 3d models

Oculus Gunstock Controller for Quest 2 3 Files - 6 parts total (1 x Stock, 2 x handle pieces, 2 x dowel pieces) Additional Parts Required: 7/8" Dowel (3 ft) 8 x Countersunk Magnets (from McMaster Carr https://www.mcmaster.com/5862K225/) 26 x Small...

Credit to sanlaki July 10, 2020 https://www.thingiverse.com/thing:4538594 Magnetic Gunstock for Oculus Quest 1, Quest 2 This gunstock is an amazing design. I've used it in 200+ hours of Pavlov VR with my Quest 2. I have modified the original...

This is a model I designed for a friend, It is an adapter for the original oculus quest to hold the oculus elite strap!

*Work In Progress - Not responsible for any damage to controllers or surroundings* **Beat Saber Grips for Oculus Quest 2 Touch Controllers** Goals/Features: * Quick installation/removal * Uses existing wrist straps * Grip position close to default...

Designed to tight-fit the stock golden AA batteries that came with the Quest 2, found out that it may be way too tight for rechargeable AA batteries so consider scaling up if you find that my AA model size isn't quite the same as the batteries you...

this quest 1 grip attatchment was moddled for a driver shaft that was cut from an old driver to a length of 24". The upper part grips the quest controller snug. there is a spot on the lower to put velcro or zip-ties. ...it works well and I hope it is...

These are small adapters that can be printed off without support that allow you to secure the Oculus Rift headphones with a M3 thumb nut to the adapter. ... The adapter can then simply be slid onto the Oculus Quest 2

... This print allows me to have a very good fit with no gaps and keeps the headset well secured. Prints flat and then snaps together. As printed it is for a XXL head size but was designed so it can be adjusted by cutting off chevrons as needed.

This model requires a 1.5m hook-and-loop fastener. ... You should cut the hook-and-loop fastener to 5pices. 3 for the battery - mount, 2 for the mount - strap. ... The battery must be mounted upwards.

... the layard. To install the layard: first put the lanyard in the hole, then loop over the clip and secure it in the 2 little hooks on each side. See photo. That how I install it but may be you will an other way haha. ... Print it flat, it's easier

... Then loop over the clip and secure it in the 2 little hooks on each side. See photos. ...That how I install it but may be you will find an other way haha.Print it flat, it's easierPrint SettingsRafts:NoSupports: NoInfill: 100Filament: PLA Grey

Motion controller handles for a better gaming experience and a better, more secure grip. Well fitted - no slack, they stick firmly + additional anti-fall protection on the string We put on the handles with the letters on the outer sides (L - left,...

Headband for DAS Mod, includes a a buckle you have to glue on top so you can slide the end of your DAS nicely under it. Print with support everywhere. ... Remixed from: https://www.thingiverse.com/thing:3664951

... Science in Engineering,* 1–12. [https://doi.org/10.1115/1.4062889](https://doi.org/10.1115/1.4062889) See also the [GitHub repository](https://github.com/virtual-prototyping-lab/olfactory-display-for-metaverse) with code and instructions.

Headband for DAS Mod, includes a a buckle you have to glue on top so you can slide the end of your DAS nicely under it. ...Print with support everywhere.</p><p>Remixed from: <a...

... is slide-in assembly. ...The main purpose of using the sliding-in installation design is to reduce possible damage to the main body of the VIVE DAS during installation. please refer to the animation for details. ... https://youtu.be/6U42l7SylNM

The headset mount is a remix of a design from lensfort on Thingiverse that allows me to hang it on my pegboard: https://www.thingiverse.com/thing:4630669The controller mounts are an original design.You'll need support material to print the hooks for...

Composite version: Parts: 3d printed components long thin-walled 3/4" tube many short m2 screws 4-6 m3 screws + nuts 4 m4 screws + nuts 100% printable version: Assembly: Insert tube pieces into each other and push in the flexnails, adhesive/acetone...

Wall mountable Oculus Quest 2 holder for headset & hand controllers with base and raised Oculus logo.

This is meant to attach to the elite strap on the Oculus quest or quest 2 to assist in holding the wire up so it doesn't wear out your charge port while playing on PC. ...Feel free to edit to your liking and you don't have to follow the same print...

It appears that this is a large block of text that seems to be a tutorial or guide for creating and using a 3D printed rifle accessory, specifically designed for use with the Oculus Quest VR headset. However, I'll do my best to break it down and...

(Respect the Geneva Convention!) Set extra thickness appropriate for the prescription and refractive index of your lenses: Likely 0 mm for +1 diopter and lower, maybe 1.2 mmm for +2 diopters, and higher for higher. Select parts to print. You need...

this is a remix from 2 people i sew, and i just orderd my oculus quest 2 so i want a docking station, you need support the controllers stand and for the controller stand attach with the oculus stand. there is the final result give like and follow to...

Oculus Quest 2 compact stand, no glue or screws required. You can add foam padding at the top, so the headset lays on a soft surface. Update 2023/01/22: Finally updated for the new Meta logo ! Added 5 files: To keep the old stand with the Oculus...

This is a clean version of the developer released 3d files from oculus for the quest 2 controllers. Scaled to in in-person measurements. Hopefully people can use this to make some cool oculus accessories. ...Please let me know if you have any issues.

Couldn't find a dock for the Oculus Quest 2 that I liked, so I made my own! Design goals: - Easy to print with no supports needed - Small footprint - Protects Quest 2 lenses by completely covering them If anyone has design ideas to also mount the...

Couldn't find a dock for the Oculus Quest 2 that I liked, so I made my own! Design goals: Easy to print with no supports needed Small footprint Protects Quest 2 lenses by completely covering them If anyone has design ideas to also mount the...

This is an Oculus Quest 2 dock for the headset and its two controllers. There is also a notch for the charging port to sit in while the headset is fully charged. I printed out a prototype and added in extra notches for the controller index finger...

Simple hanger I made for my Oculus Quest. Looks good while keeping short print times, took about 2.5 hours for me. The pieces can be used for either side, so print two of each to hang the headset. I would use supports but forgot to turn it on in...

Here is a rewritten version of the original text: "I'm offering a high-quality 3D model of Oculus Quest 2 controllers, featuring excellent topology and detailed textures. The file format is FBX, which includes four high-resolution PNG files: base...