golf club for oculus quest 2 3d models
3371951 3d models found related to golf club for oculus quest 2.thingiverse
An adapter to glue a broken old shaft (or a cut new one) and grip together which works in the Golf+ app for the Oculus QUest 2. Two velcro straps of 10 cm are required to mount the controller (left handed or right handed version). Can be printed...
thingiverse
This extension allows to attach your Quest 2 controllers to a real golf shaft. Get you hands on some old putter or other club and cut the shaft in half. Now you can fasten the printed part to the shaft with 2 nuts and bolts. Alternatively you could...
thingiverse
Drilling holes in each side of the gold club tube for the bolt was not easy. I had a hard time, tried different things, was even thinking of buying a small drill press. But ended up using a Dremel with a cutting blade to just cut a small slit where...
thingiverse
Mount a right hand Oculus Quest controller to a Golf club shaft. This requires 4 screws/bolts ~M4 size and 32mm length. I used lock washers and wing nuts with the bolts as well as 2 6.5mm nylon spacers for the middle section of the clamp. The...
thingiverse
4894874/5411253To assembly you need 2 M3 Bolts & screws, im using 20mm.The hole in the club is 3.5mmPrinted in TPUNot tested in PLA ( I think it would not work because the hole where you put the controller works with friction )For the infill, i have...
thingiverse
This is my version of a golf attatchment made specifically for my Oculus Quest 2! I tried to make the design as similar to Deadeye VR's product as possible. So instead of spending $70 I only spent $10! The controller should fit inside the print very...
thingiverse
This mount was specifically designed for use with Walkabout Mini Golf on the Oculus Quest 2, and is intended to (more or less) map the angle of the physical putter to the in-game virtual putter. As such, it might not map as well to clubs in other...
thingiverse
This mount was specifically designed for use with Walkabout Mini Golf on the Oculus Quest 2, and is intended to (more or less) map the angle of the physical putter to the in-game virtual putter. As such, it might not map as well to clubs in other...
prusaprinters
... belt strap to secure your controller. ...You can get them here: https://sanlaki.shop/products/golf-club-diy-kit Walkabout Minigolf - set angle to 38Golf+ - use Sanlaki preset (currently broken, working with devs to get the alignment sorted out)
thingiverse
I found the best success with the "CUSTOM" club in the golf+ settings and aligning the remote onscreen with the actual location of the remote on the golf club handle in real life. The dead eye works but custom seems better. The picture shows using...
thingiverse
After noticing how easy it was to remove the regular strap from the Oculus Quest 2 controllers I figured I'd take a quick stab at making a "Knuckles" like experience so you don't have to keep your hands firmly gripped on the controllers. Print 1 of...
thingiverse
It's designed to handle an Oculus Touch controller into a shaft of a real golf club to be used in __a game who allow to use theses__ specific controllers (Golf Club VR). Depending of the print and printer quality, it no need to print supports. I...
thingiverse
I take no responsibility whatsoever if this printout breaks down during gaming, and destroys your Oculus control or anything else in your home. Read the ReadMe.docx for instructions... ... The clip could be scaled down to around 97% for a tighter...
cults3d
For a long time I was looking for some nice lightsaber with which to play a good beat saber. so I decided to make it myself :) The lightsaber is fully printed consisting of two parts. ... unprintable part: the non-printable part is a threaded rod...
thingiverse
This is a remix of https://www.thingiverse.com/thing:5204772. ... I needed to make it a bit stronger as it broke off at one point. There are also 2 different versions, 13.5 and 14.5 shaft diameter.
thingiverse
STL and Fusion 360 file are provided.It does not have a swivel joint, so this will not move.You need to know how to remove the Quest 1 support arms (can be reversed), please see instructions...
thingiverse
Oculus Quest 2のバッテリーを拡張するマウンタです。 Anker PowerCore 10000を、標準ストラップの後頭部に固定します。 Extend Battery for Oculus Quest 2 ・Anker PowerCore 10000 ・USB Cable (Type A to C) ・Rubber Band (Size 31)
thingiverse
Just a clip for hanging cable. ... *Design for Oculus Quest 2
thingiverse
Hello Oculus Quest 2 fans, Here is SECOND EDITION of Saber Handles with the following improvements... . Quick attach/detach with locking mechanism - no tape or screwdriver required! . Ergonomic improvements for multiple hand positions . ...
thingiverse
Table tennis adapter for Oculus Quest 2 touch controller. ... The battery case have to be removed and the controller inseted to the adapter.
thingiverse
Updated The_Math_God adapter for Oculus Quest 2 Different diameter for the lanyard as AMVR did change it with newer models. ... I personally did use the 3mm diameter without issue.
thingiverse
I remixed the Oculus Quest 2 DAS Adapter for my GoQuestVR Halo Strap (it might work with other type of Halo straps, I suppose they are all pretty much the same). I did not like the original fitting that was limited in the rotation and also the fact...
thingiverse
... to avoid the clamps at the top. ... To secure the Oculus Quest 2 controllers in the grips, I opted for a screwable cover at the bottem that wedges in the grip cords. ... Prints need support and you will need 2 M3 screws per grip between 10-14 mm long.
thingiverse
One handed gunstock for gun games on oculus quest 2 Got inspiration from Istock that's you can buy on Etsy Used the grip from Sierra's design I made this for myself but uploaded it so other people can use it No supports 25% infill
thingiverse
[ENGLISH] Oculus Quest 2 holder for Ikea Skadis Designed on FreeCAD 0.18 (original file attached). Made on an Ender 3-V2 printer. Printed in PLA, 15% fill, 0.20mm, no support if printed as shown, 10h06 printing. Mounted with 4 x 50 screws, from...
prusaprinters
I remixed the Oculus Quest 2 DAS Adapter for my GoQuestVR Halo Strap (it might work with other type of Halo straps, I suppose they are all pretty much the same). I did not like the original fitting that was limited in the rotation and also the fact...
prusaprinters
Oculus Quest 2のバッテリーを拡張するマウンタです。 Anker PowerCore 10000を、標準ストラップの後頭部に固定します。 Extend Battery for Oculus Quest 2 ・Anker PowerCore 10000 ・USB Cable (Type A to C) ・Rubber Band (Size 31) Print Settings Printer Brand: Prusa Printer: I3 MK3SRafts: No...
thingiverse
VR PADEL adapter for Oculus Quest 2. Compatible with two PADEL simulators: VR PADEL https://www.vr-padel.com or PADEL VR https://www.padelvrgame.com You will need to cut a real padel racket. It is easy to find a broken one. Cut the racket...
thingiverse
Installation method can refer to: https://youtu.be/GrZ31cYY-2Q You can also get this product here:...
cults3d
REMIX of https://www.thingiverse.com/thing:4077392 made by prahjister Addition of the OCULUS logo on the front of the monoblock base print base with logo + TopV2 Adding the slot for the OCULUS logo + the OCULUS logo to be inserted for the bi color...