go pro sesion 5 3d models
701376 3d models found related to go pro sesion 5.
thingiverse
I wanted this grip to excel in providing flotation support so that even if you accidentally let go of your camera underwater while scuba-diving, it stays safely above the water's surface instead of descending into the unknown depths. For optimal...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_rod_d = 55 gopro_primary = triple gopro_secondary_what = clamp gopro_secondary_rotated = 0 gopro_bar_th = 5 gopro_rod_nut_od = 8.05...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_ext_th = 6 gopro_rod_nut_od = 8.05 gopro_captive_rod_angle = 45 gopro_bar_gap = 2.4 gopro_rod_nut_th = 3.6 gopro_captive_rod_id = 3.8...
thingiverse
... each with a length of over 10 millimeters. ...Additionally, you will need 2 M4 nuts and epoxy glue for securing the nut to the mount. The specified belt width is 25 millimeters. The thickness of the belt ranges from 1 millimeter to 3.5 millimeters.
thingiverse
Using the following settings: * gopro_primary equals triple * gopro_secondary_what equals double * gopro_captive_rod_id equals 3.8 millimeters * gopro_ext_th equals 6 millimeters * gopro_ext_len equals 30 centimeters * gopro_rod_nut_th equals 3.6...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following settings: gopro_bar_screw_head_d = 6.2 millimeters gopro_bar_th = 4 inches gopro_bar_rod_d = 43 centimeters gopro_bar_screw_shoulder_th = 4.5 centimeters...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_captive_rod_angle = 45 gopro_rod_nut_od = 8.05 gopro_ext_th = 6 gopro_rod_nut_th = 3.6 gopro_ext_len = 50 gopro_primary = triple...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_screw_nut_d = 6.01 gopro_bar_gap = 2.4 gopro_ext_len = 30 gopro_secondary_what = double gopro_ext_th = 6 gopro_primary = triple...
thingiverse
To create this customized model, specific parameters were used including a 45-degree angle for the GoPro captive rod, a triple setup for the secondary GoPro, a protruding height of 0.5, a shoulder thread diameter of 4.5 for the bar screw, a rotated...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_screw_shoulder_th = 4.5 gopro_secondary_what = triple gopro_bar_screw_d = 3 gopro_captive_rod_angle = 45 gopro_captive_protruding_h =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_ext_th = 6 gopro_bar_screw_shoulder_th = 4.5 gopro_primary = triple gopro_rod_nut_od = 8.05 gopro_secondary_rotated = 1 gopro_captive_rod_id...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_secondary_rotated = 1 gopro_bar_th = 3.2 gopro_ext_len = 50 gopro_captive_rod_angle = 45 gopro_bar_screw_nut_d = 6.01 gopro_rod_nut_od =...
thingiverse
Thingiverse.com/Apps/Customizer/Run?Thing_id=322897 Instructions Using the Following Options: Center Width = 3.3 Width = 14.3 OD = 15 Supports = 1 Gap = 3.1 Captive Nut OD = 11 ID = 5.3 Female Snap Fit Tolerance = 0 Male Snap Fit Tolerance = 0 Snaps...
thingiverse
... I opted to design and fabricate it myself. When resizing, ensure that the outer dimensions measure 17.5 millimeters in one direction and 23.6 millimeters in the other, specifically targeting the square section rather than the connectors with holes.
thingiverse
This design has specific measurements for various parts like gopro_bar_screw_shoulder_th (4.5), gopro_captive_protruding_h (0.5), and gopro_ext_len (50). The primary mount is a triple setup, with optional secondary mounts as doubles. Other key...
thingiverse
... (M4x10 can also work). The cylindrical head is essential as it will rotate. 5. M4 nut with neoprene ring ISO 7092-4-200HV. Can be replaced by two regular nuts possibly with a split washer in between. ...This nut should not come loose when turned.
cults3d
Best go pro hero 5, 6, 7 mount you'll find, lol. I designed this one because I couldn't find one that fitted my needs. Print in TPU, you can print it with 20% infiil and set 8 top and bottom layers to make the tabs solid. ...Print on its side, the flat...
thingiverse
Best go pro hero 5, 6, 7 mount you'll find, lol. I designed this one because I couldn't find one that fitted my needs. Print in TPU, you can print it with 20% infiil and set 8 top and bottom layers to make the tabs solid. ...Print on its side, the flat...
thingiverse
Adapter Plate for GoPro Hero 5 lets you utilize Lenses from Session.
thingiverse
This creation was crafted using Tinkercad's robust tools. ...Make adjustments and refine it in real-time at https://www.tinkercad.com/things/85ExIZOSHCU.
thingiverse
This creation is based on Tinkercad technology. ...Make changes directly online at https://www.tinkercad.com/things/59YXaLhaGDC.