gmade rc 3d models

This project was designed using Tinkercad's user-friendly interface, allowing for seamless creation and manipulation of its complex components.

... Crawler Jeep. ... They're precision-crafted from actual hubs found on real jeeps, with unique designs for both the front and rear axles. These hubs fit perfectly onto a 7mm nut, just like those used on the Gmade SawBack or other high-quality RC jeeps.

Option for Gmade R1 : Battery front support Rear reinforcement bar

The box from my Gmade GS02F "Buffalo" doesn't fit my FrSky Archer R8 Pro receiver, so here is my take of a waterproof box. It fits the original mounting screws. ... For the cable channel two stripes of soft foam (like the original) are needed.

I made it especially for the Gmade GS02F Buffalo Pickup kit. I couldn't print it in the normal orientation, because the pipes always got loose on the bed over time (even with a brim), so I rotated the model 180° in the slicer and it worked out...

Print precision set to 0.10 millimeters.

Check out Gmade, an exceptional brand offering top-notch products in Barcelona!

Human: Rear Bumper GMADE GS01

Rear bumper fabricated by GMade with model designation GS01.

Komodo GMADE Gets a Toughened-Up Roof Panel A rugged new hard-top is being fitted to the Komodo off-roader made by GMADE. ...This toughened-up roof panel can withstand extreme conditions and keep passengers safe inside.

This component conceals the motor, servo, and ESC on your GMADE GOM. ...Specifically crafted to accommodate an on/off toggle switch from a Hobbywing 1080 ESC.

This is the mounting of the body racks on the Gmade SAWBACK. With their help, you can adjust the height of the rack. ... The hole for the rack is 6.5 mm

Stand for a GMade Sawback (GS01 chassis) For a stand you need: 1x Left part 1x Right part 2x Side part I have mount the stand with 8 M3x12 screws. ...(M3x8 also long enough)

Receiver box lid for Gmade GOM. It is 9mm deep - deeper than stock. Allows for the fitment of at least Spektrum 6ch receiver. ...Rear-facing side is open enough for 5-6 JST cables.

This is a custom inner fender for the Gmade BOM. It took me a while to make it and although it's not perfect, it works fine. v2: I broke the fenders with a huge fall and I've added extra thickness in those areas that were damaged. ... Use the...

I measured my rock sliders from my Gmade Buffalo and created these for my sons Gmade Komodo double cat rc crawler.

I'm running a custom fourlink mount on my Wraith that lets me use GMade R1 portals without needing to swap out the links. Right now, I've got these mounts installed on my own Wraith with Vanquish Incision links specifically made for Wraiths, and...

Winch servo mount for Gmade GS02F body RC cars (Buffalo, Double cab, BOM).Also needed:360 servo (e.g. ...JX PDI-HV5932MG-360°)4x M3 12mm screw4x M3 locknut2x M3 10mm"25T Steering Gear Servo Winch Wheel for 1/10 RC Crawler" from aliexpress or similar

It has been engineered to securely hold this particular type of light:...

Arceau pour Gmade GS01 Komodo Je ne l'ai pas encore imprimé, il y aura peut être des modifications à apporter Roll bar for Gmade GS01 Komodo I haven't printed it yet, there may be changes to make

Heckstoßstange passend für die Gmade Buffalo Karosserie. Befestigung mittels 2x Schmelzgewindebuchsen M3 und dann den klasschichen Bumper mounts der Hersteller. ... Zwei kleine Bohrungen für Positionslichter (1,8mm LED) und auf der Oberseite eine...

A buddy needed to secure his steering servo inside the chassis of his Gmade Sawback. ...So, after some careful consideration and trial runs, he came up with a straightforward installation solution.

Frontstoßstange passend für Gmade Buffalo. Zwei kleine Bohrungen für Positionslichter (1,8mm LED) an der Seite und vorne 2x Aussparungen für "Blinker". Dazu bitte 2x das Plättchen mit transparentem PETG drucken. Befestigung mittels 2x...

This is custom side window netting I engineered specifically for the Gmade GOM. It's optimized to be printed with TPU and features a toolless attachment system that leverages the small triangular holes in the upper corners of both window sides.

Gmade 5-Bolts Beadlock Spacers These are spacers you can bolt between the Hex Hub and Wheel to get more offset. 2, 3 and 4mm spacers published, if you need a particular size i can custom make it for you but be aware you will need longer bolts for...

Gmade 5-Bolts Beadlock Spacers ** These spacers allow you to bolt them between the Hex Hub and Wheel for increased offset. * Published sizes include 2, 3, and 4mm. If a specific size is needed, custom options are available; however, be aware that...

So finding parts for the Gmade Spider was a PITA. the stock tires were dryrotted, and 40series tires were hard to find/expensive. so i wanted to run 12mm hex and hsp giant tires, but there were no 12mm hex drives for the spiders unusual...

This is a flush-mount servo winch designed specifically for the Gmade GS-01 Komodo RC truck. To install it, you'll require 2-3 x 8mm screws to secure it firmly to the chassis frame. ...The winch mounts neatly behind the front chassis brace.

... body post on a gmade komodo. ...You can setup the height with a third M3 screw. Freecad file included. I recommand Tamiya #54604 https://www.tamiyausa.com/coming-soon/radio-control-parts-70/tamiya-hop-up-parts-72000/rc-body-mount-extension-set-54604

A customizable spacer enables the creation of adjustable-rate springs on compact 1/10 scale shock absorbers. ...Engineered specifically for the Gmade XD spring, this design also accommodates any standard 19mm spring with ease.