gmade gs02 3d models

Check out Gmade, an exceptional brand offering top-notch products in Barcelona!

Human: Rear Bumper GMADE GS01

Rear bumper fabricated by GMade with model designation GS01.

Komodo GMADE Gets a Toughened-Up Roof Panel A rugged new hard-top is being fitted to the Komodo off-roader made by GMADE. ...This toughened-up roof panel can withstand extreme conditions and keep passengers safe inside.

This component conceals the motor, servo, and ESC on your GMADE GOM. ...Specifically crafted to accommodate an on/off toggle switch from a Hobbywing 1080 ESC.

Receiver box lid for Gmade GOM. It is 9mm deep - deeper than stock. Allows for the fitment of at least Spektrum 6ch receiver. ...Rear-facing side is open enough for 5-6 JST cables.

This is the mounting of the body racks on the Gmade SAWBACK. With their help, you can adjust the height of the rack. ... The hole for the rack is 6.5 mm

Stand for a GMade Sawback (GS01 chassis) For a stand you need: 1x Left part 1x Right part 2x Side part I have mount the stand with 8 M3x12 screws. ...(M3x8 also long enough)

This is a custom inner fender for the Gmade BOM. It took me a while to make it and although it's not perfect, it works fine. v2: I broke the fenders with a huge fall and I've added extra thickness in those areas that were damaged. ... Use the...

I'm running a custom fourlink mount on my Wraith that lets me use GMade R1 portals without needing to swap out the links. Right now, I've got these mounts installed on my own Wraith with Vanquish Incision links specifically made for Wraiths, and...

Option for Gmade R1 : Battery front support Rear reinforcement bar

I measured my rock sliders from my Gmade Buffalo and created these for my sons Gmade Komodo double cat rc crawler.

Arceau pour Gmade GS01 Komodo Je ne l'ai pas encore imprimé, il y aura peut être des modifications à apporter Roll bar for Gmade GS01 Komodo I haven't printed it yet, there may be changes to make

A buddy needed to secure his steering servo inside the chassis of his Gmade Sawback. ...So, after some careful consideration and trial runs, he came up with a straightforward installation solution.

Heckstoßstange passend für die Gmade Buffalo Karosserie. Befestigung mittels 2x Schmelzgewindebuchsen M3 und dann den klasschichen Bumper mounts der Hersteller. ... Zwei kleine Bohrungen für Positionslichter (1,8mm LED) und auf der Oberseite eine...

Frontstoßstange passend für Gmade Buffalo. Zwei kleine Bohrungen für Positionslichter (1,8mm LED) an der Seite und vorne 2x Aussparungen für "Blinker". Dazu bitte 2x das Plättchen mit transparentem PETG drucken. Befestigung mittels 2x...

Winch servo mount for Gmade GS02F body RC cars (Buffalo, Double cab, BOM).Also needed:360 servo (e.g. ...JX PDI-HV5932MG-360°)4x M3 12mm screw4x M3 locknut2x M3 10mm"25T Steering Gear Servo Winch Wheel for 1/10 RC Crawler" from aliexpress or similar

This is custom side window netting I engineered specifically for the Gmade GOM. It's optimized to be printed with TPU and features a toolless attachment system that leverages the small triangular holes in the upper corners of both window sides.

This is a rear light holder designed specifically for GMade Gom. ...It has been engineered to securely hold this particular type of light:...

Gmade 5-Bolts Beadlock Spacers ** These spacers allow you to bolt them between the Hex Hub and Wheel for increased offset. * Published sizes include 2, 3, and 4mm. If a specific size is needed, custom options are available; however, be aware that...

Gmade 5-Bolts Beadlock Spacers These are spacers you can bolt between the Hex Hub and Wheel to get more offset. 2, 3 and 4mm spacers published, if you need a particular size i can custom make it for you but be aware you will need longer bolts for...

So finding parts for the Gmade Spider was a PITA. the stock tires were dryrotted, and 40series tires were hard to find/expensive. so i wanted to run 12mm hex and hsp giant tires, but there were no 12mm hex drives for the spiders unusual...

A customizable spacer enables the creation of adjustable-rate springs on compact 1/10 scale shock absorbers. ...Engineered specifically for the Gmade XD spring, this design also accommodates any standard 19mm spring with ease.

This is a flush-mount servo winch designed specifically for the Gmade GS-01 Komodo RC truck. To install it, you'll require 2-3 x 8mm screws to secure it firmly to the chassis frame. ...The winch mounts neatly behind the front chassis brace.

Hello, It's a small part to fix 6mm standard body post on a gmade komodo. You can setup the height with a third M3 screw. Freecad file included. ... I recommand Tamiya #54604 ...

i made this for the snowplow from daver18qc https://www.thingiverse.com/thing:4094959 It fits a gmade buffalo without bumper But! You need to construct something to hold or stop it from moving to the frontaxle. He mentioned this. ...You can somehow...

Hello, It's a simple fix to upgrade the 6mm standard body post on your Gmade Komodo. To customize the height, just add a third M3 screw. You can download the Freecad file included in this update. ...For the best results, I recommend using Tamiya #54604.

Customizable mounting system designed specifically for Gmade R1 portal axle upgrades, allowing users to tailor the position of their steering components for optimal performance and adjustability. The innovative center-link design provides maximum...

**Made specifically for Gmade GS01 frame w/ Leafs** **For an Axial SCX10.2 version check here: https://www.thingiverse.com/thing:4050732** This is the same snow plow as my Unimog one, but with a key difference - you can attach this one directly to...

Fender fits to Reely Freemen / Axial SCX10. ... Specially Designed for the Gmade Buffalo Body.