glass sodastream bottle 3d models

I designed this to keep the CO2 bottle for my budget aquarium C02 fertilizing from tipping over. Fits an 425g C02/60 Liter/ 60mm diameter CO2 bottle Print instructionsUsed PLA, 0.3mm Layers

A clip to attach to the dish dryer to drain bottles,printed in PLA 0.3 mm layers with 50% infill with 10 perimeter shells for strength an flexibility 

A clip to attach to the dish dryer to drain bottles,printed in PLA 0.3 mm layers with 50% infill with 10 perimeter shells for strength an flexibility

I built a device to secure the 425g CO2 tank for my affordable aquarium CO2 feeding system, so it won't tip over. ...It fits perfectly on a standard 60-liter, 60mm-diameter CO2 bottle.

Hi there, This is a DIY project to dry bottles for a Soda Stream machine. The design is a reworked concept, but I've incorporated hexagonal elements into it. ... Best regards from Germany, Andreas

This design fits perfectly on German (and possibly other) refundable PET bottles. ... Edit: Check out my updated version at https://www.thingiverse.com/thing:1953920 Print Settings: Printer: Prusa i3 Rafts: No Supports: No Resolution: 0.2 Notes:...

Based on a bottle cap and inspired by a bottle stand, i needed more than an only one bottle stand, so i designed this and remodel all the thing with more bottle space and my own design. CAUTION: The 3 and 6 bottles models need a print bed that can...

Was looking for a good bottle holder that would drain towards the sink.  Most were either too elaborate or didn't drain away.  This one is to the point and works great.v2 - Wider, longer, taller, edges lifted to keep it from draining in the wrong...

The bottle stand vertically and firmly. Any water droplets that may fall out will land on a printout, so it won't wet your table. I've done 3 of those and they all work fine for several months now. It should be done in 1,5 hour tops. ... Enjoy :)

Small bracket to keep soda stream CO2 bottles from rolling around on the counter. Print instructionsPrinted in PETG, 13.13 m filament used. Better print quality enabling supports (but have printed without. First shared model - hope its helpful...

Small bracket to keep soda stream CO2 bottles from rolling around on the counter. Print instructionsPrinted in PETG, 13.13 m filament used. Better print quality enabling supports (but have printed without. First shared model - hope its helpful...

An additional handle that helps to open the bottle cap of SodastreamFor people who has difficulty on opening the cap due to its just round design.My partner sometimes needed my help to open it, so originally i made this opener for her.If someone has...

... design your own one if need it. For printing, you can use PLA with a layer high 0,2 mm. It will need approximately 40g of material. More pictures you can find here. https://www.printables.com/cs/model/177666-bottlesodastream-bottle-drying-rack

Sodastream Bottleholder for 3 Bottles and Caps

To dry my four PET bottle, which I am using for my SodaStream device I develop a dryer stand To see which part has to be printed who often, see the ReadMe file There also exist a one, two and three bottle version: One bottle...

To dry my one PET bottle, which I am using for my SodaStream device I develop a dryer stand To see which part has to be printed who often, see the ReadMe file There also exist a one, three and four bottle version: One bottle version:...

To dry my one PET bottle, which I am using for my SodaStream device I develop a dryer stand To see which part has to be printed who often, see the ReadMe file There also exist a two, three and four bottle version: Two bottle version:...

... should only be used standing upright, I built a holder for the bottles. The holder is designed for Sodastream bottles with a diameter of 6 cm. It has a screw hole to be screwed to a wall. ...The bottle is fixed in the holder with a rubber band.

This is a working model of the top of a sodastream bottle. ... It screws nicely into the caps and the regassing unit.

A small kitchen gadget to hold your Sodastream bottle and the cap. I have printed it laying on the side so it is super stiff. ... Category: Kitchen & Dining

A SodaStream Bottle Cap with a nice design and handle. ... 0,20mm Resolution, Support on the built plate only, infill 20%.

A SodaStream Bottle Cap with a nice design and handle. 0,20mm Resolution, Support on the built plate only, infill 20%. PLA. ...Used Creality Ender 3 Pro.

A small kitchen gadget to hold your Sodastream bottle and the cap. I have printed it laying on the side so it is super stiff. ...

Twist and pull to remove it.Designed for line width of 0.4mm and 3 walls, prints without infill nor supports (max 20° overhang).Two files, two different designs:SodaStream_bottle_base_v01.stl has vertical exterior...

Inspired by [SodaStream Base for 1 L Slim Bottles](https://www.thingiverse.com/thing:4569019) by [filerm](https://www.thingiverse.com/filerm/designs) and [SodaStream bottle holder](https://www.thingiverse.com/thing:5422282) by...

As these bottles should only be used standing upright, I built a holder for the bottles.The holder is designed for Sodastream bottles with a diameter of 6 cm. It has a screw hole to be screwed to a wall. ...The bottle is fixed in the holder with a...

...not really a "source file" remix but a reinterpretation of the basic design done from scratch in FreeCAD with some refined edge chamfers - parametric *.FCStd file is included Dimensions are fitted to the much more chunky SodaStream Crystal Bottle...

The original PET adapter this is based from works so well, that I (digitialy) reamed out the PET thread and replaced it with one that fits the 375ml VOSS Water Bottles as we have a few of these around the place and they make a nice alternative to...

This bike bottle holder takes a large sodastream fuse bottle and holds it steady. It will need a thin 1 inch square pad halfway between the mounting points inside to stop bottle rattles. A bit of mouse mat is perfect. Make sure you print in PETG or...

A SodaStream Bottle Cap with a nice design and handle. 0,20mm Resolution, Support on the built plate only, infill 20%. PLA. ...Used Creality Ender 3 Pro.</p>