glass bed for flashforge creator pro 3d models

Flashforge Creator X users opting for a 3mm glass plate can use the provided shim to account for the additional thickness. However, this adjustment reduces build plate height by approximately 3 mm due to the Creator X's thicker construction compared...

Printer Settings: Printer Model: FlashForge Creator Pro Supported by Printer: Yes Resolution Level: 0.3 Infill Rate: 40% Notes on Printing: To get these prints done, I set all three pieces to print in 0.3mm layers with a 40% infill ratio - except...

Print Settings for this part are listed below: Printer model: FlashForge Creator Pro Yes, it does generate rafts during printing It doesn't have built-in support material. However, the option might not matter given that the infill density will reach...

This is an anti-vibration foot for a FlashForge Creator Pro. It has a base cup to hold the anti-vibration material, a foot pad for the printer and a template for cutting the anti-vibration material. I created this because I had extra sorbothane left...

This is a small but crucial upgrade for the latest edition of the FlashForge Creator Pro. The purpose of this upgrade is to keep the umbilical cord between the printer and nozzles firmly upright. Without it, the cord tends to sag to one side on my...

By default, the dimensions of this model incorporate a compact SD slot that facilitates seamless compatibility with SD sockets equipped with a 'push-to-release' mechanism, such as those found in Flashforge Creator Pro models. One notable advantage...

I love my Flashforge Creator Pro except for one ergonomic problem: when I stand next to it, I simply cannot see the display because it's too low and vertical. I need either to step back or bend down. Not anymore. This design provides a 45% slanted...

The default dimensions have a short SD slot that enables use with an SD socket featuring a 'push it to release' mechanism, such as the Flashforge Creator Pro. The model comes equipped with a built-in support wall, which facilitates easy printing...

The default dimensions boast a short SD slot that enables seamless use with an SD socket featuring a 'push to release' mechanism, like the one found in Flashforge Creator Pro. A built-in support wall is integrated into the model, allowing for...

Mold is made to create silicone boots for the Flashforge Creator Pro 2016 printer. To get the mold right, a regular two-part silicone mix was used. However, high-temp silicone mix has been ordered to make the final boots:...

I love my Flashforge Creator Pro, but one ergonomic problem was driving me crazy - when I stood next to it, I couldn't see the display because it's too low and vertical. I had to step back or bend down just to check settings. No more. This design...

... about 1" off the length of the filament guide tubes that are provided with the printer. Print Settings Printer: Flashforge Creator Pro Rafts: Yes Adhesion Type: Magigoo Supports: No Resolution: High/Slow Layer Height: 0.2mm Infill: Medium - 30%

... require more complex printing, necessitating supports, etc. I did use a raft because the base is very thin, but trimming the end would likely allow printing without it. Printer settings: Printer: Flashforge Creator Pro Rafts: Yes Supports: No

This is a simple side mounted PTFE tube holder for the Flashforge Creator Pro. The one that comes with the machine mounts to the back, and is best suited for mounting your spools to the back as well, but with a configuration like mine where you can't...

... 60mm in length and are spaced 81mm center to center. Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: Yes Resolution: 0.20mm or less Infill: 15% - 100% Notes: The model was printed upside-down with adequate support throughout.

... a small end stop within the tube's nozzle. Print Settings: Printer: Flashforge Creator Pro Rafts: No rafts will be printed Supports: Print supports are enabled Resolution: 0.3mm resolution is selected Infill: 20-25% infill density is chosen

Use these brackets to attach rubber isolation pads securely to the Flashforge Creator Pro. The brackets replace standard covers that usually sit on printer bases. ...Replace rubber feet pads with JW Winco GN 451 Cylindrical Vibration Isolation Mounts...

I got tired of threading the needle to get my filament loaded on my FlashForge Creator Pro and my previous filament tube holder wasn't sticking out far enough after I started using my low friction spool holders, so I created this thing to make...

This product specifically caters to the late 2014-2015 models of the Flashforge Creator Pro with slot spool holders. Best results are achieved when printing this model sideways, using supports at a 45-degree angle. This creation was influenced by...

This holder was created for securing spray bottles and parts at the corners of a flashforge creator pro printer. As seen here, you can insert whatever fits inside it. Instructions A corner solution was sought out to hold multiple...

------------------- I dislike the spool holder of the FlashForge Creator Pro 2016. Smooth rotation can be difficult depending on the filaments manufacturer. I have tested various systems and now use my own design. This system works with both big...

Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: Yes Resolution: .2mm Infill: 20% Notes: Supports were only added to the drawer and infill was set to 100% for both the drawer and pegs. The drawer was printed horizontally. ...I...

The ultimate bridge upgrade for the Flashforge Creator Pro is now a reality! With its sleek, rounded profile, this bridge effortlessly guides cables across its span, eliminating friction and preventing wear on your valuable equipment. The result:...

This is a custom handle for the Improved Dome that fits perfectly on the Flashforge Creator Pro. It makes it simple to detach and reattach the dome with just one hand. The design was created by modifying a parametric handle generator, allowing you...

Things You'll Need for This Project (Double Up If You're Making Both Left and Right Spool Holders) 2x Ball Bearings No.6003 (OD 35 mm, ID 17 mm, Thickness 10 mm) 1x Holder.slt (Printed Part) 2x Cone.slt (Printed Part) 1x Nut.slt (Printed Part) Print...

... completed. Instructions This project was made without support during printing and it looks like that could lead to difficulties when carving or refining your design, so try supporting during print instead and cut excess away later for clean surface

... for this moment. Hold the door open and apply gentle pressure to secure the magnet firmly in place. The Print Settings used for this model were: Printer: Flashforge Creator Pro Rafts: Doesn't Matter Supports: No Resolution: 0.1000 Infill: 25%

I love my Flashforge Creator Pro except for one ergonomic problem, when I stand next to it I simply cannot see the display because it is too low and is vertical. I need either to step back or bend down. Not anymore. This design provide a 45% slanted...

Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: Yes Infill: 30% Notes: The filament tubes fit very snugly. To get one tube to go in, I had to remove a burr. If it's too snug for your tube, try rolling up some...

I love my Flashforge Creator Pro, but one ergonomic problem had to be solved - when standing next to it, I couldn't see the display clearly because it was too low and vertical. I needed either to step back or bend down. That's no longer a problem...