glass bed for anet a8 3d models

... take note! ...I'm sharing some leftover Anet parts that might be of use to you. It appears they're made from 6mm acrylic, and although I no longer have my trusty Anet A8, I figured it's worth passing along for your enjoyment. ...Happy crafting!

i dont like the holder which are availible, so i made one fit for me .. ... here we go ..

These are front and rear plates designed specifically for an Anet A3, featuring a 10mm raised bed height. The front plate can be printed at a 45-degree angle, while the rear plate requires a more levelled surface. ...I plan to produce them from...

This is a two-piece reinforcement bracket specifically designed for the Z-stepper motors on the Anet A8 printer. It's part of a comprehensive set of printable reinforcements that have not yet been published. The lower section, highlighted in red,...

Here's the brass brush and heatbed wire holder for the Anet A8. It requires removing your heatbed, as it is mounted on the front left, atop the aluminum H frame using bearing block bolts. When tightening those bolts, don't forget to move the Y axis...

Bed Level Sensor Mount for Stock Anet or TronXY Bed Level Sensor, Designed Specifically for Remixing. Version 2: The Mount's Size Is Reduced. Version 3: The Mount is Realigned to be Centered on the Nozzle. The Distance from Nozzle to Sensor Center...

This is my custom MOSFET holder designed for my Anet A6, which should also fit the Anet A8 seamlessly.\nThe MOSFET Holder cleverly utilizes the standoffs from the microcontroller for mounting purposes.\nI have created two versions of the holder:\n1)...

This is a filament guide for rear mounted spools on the Anet A8. I made this to compliment my "Anet A8 Low Profile Top Mounted Spool Holder Assembly". https://www.thingiverse.com/thing:5145687 It should work with other setups that have spools to...

The plate's glass edge aligns perfectly with the spring-loaded centering wheel, ensuring seamless printing operations. With ABS material as the printing medium, a 0.2 millimeter nozzle and a delicate 0.1 millimeter layer height are set in place. ...To...

For Anet A8 printers with black plastic bearing mounts, printing two float mounts for the Y carriage and one for the X carriage should suffice. The fixbearing.stl file is provided for users with stock mounts of different heights. This experimental...

The Anet A8 Board requires a straightforward 70 fan setup to maintain stable temperatures during prolonged printing sessions.

The base was repurposed and is now being utilized to develop a project on the Anet A8.

These models were designed to secure: glass + hot bed + a cork layer around 3mm thick. The type of cork used determines which clip works best. It's best to try each one to see which is most suitable for your setup. Measurements: 7 - 7.5 - 8. ...For me,...

Experimental floating linear bearing mount using printed leafspring for stabilization, designed to replace stock Anet A8 linear bearings plagued by grinding problems. The stock linear bearings leave behind a residue of "pixie dust" on the rods after...

A Simple Mount for the SKR Mini E3 on Anet A8 Stock Frame This mount makes it easy to attach the new SKR mini E3 to the original Anet A8 frame. It was printed in PETG, but any material would work just as well. Printer tolerances can vary, so you...

(Check out the website from Coogle for some details: https://www.thissmarthouse.net/dont-burn-your-house-down-3d-printing-a-cautionary-tale/.) With this smoke detector bracket, you can mount a simple smoke detector above your Anet A8 printer, close...

There are a lot of Anet A8 3D Touch mounts out there, but none met my needs. I wanted the probe on the right side and in line with the nozzle, not in front or behind it. I designed this one, and it's working well for me. I have used it for some...

It includes a cutout specifically designed for the Anet A8 Fan Duct Spaceship (https://www.thingiverse.com/thing:2088006), allowing the front piece to sit flush with the parts fan without any obstructions. The design should be adaptable for similar...

I designed the "SpoolHolder ANET A8" by Madjestik58 (http://www.thingiverse.com/thing:1624641) and realized they were quite unstable, so I created an Adapter from the superior designed "Anet A8 Spool Holder Redux" by dldesign to securely attach them...

To make this, you'll need to cut it in two pieces since it's too large for a single print job on my Anet A8. Assembling the holder requires a 40cm long M8 threaded rod and some washers and nuts - just check out the pictures to see how it all comes...

Perched atop the Anet A8, a direct extruder system hums along, layer by layer unfolding its creation. The parameters are set: a modest 0.2mm layer height and an intricate 30% infill density. ...Meanwhile, Skynet3D's Marlin firmware orchestrates this...

This kit is specifically designed for relocating the original Anet A6 full graphics display to its stock mounting position on an Anet A8 printer. The idea behind this conversion is to save money by not purchasing a new frame part, which costs 25...

Here's a small, functional enclosure box for switches and LEDs designed to connect peripheral fans, LED strips, and more to my Anet A8, but it can work with any 3D printer. If you have questions about the wiring, feel free to leave a comment! Print...

... since I was having trouble getting those original ones seated properly. Make sure you assemble with M3 nuts on the bottom! Check out my innovative new product, The "OFFi" Auto-off switch for ANET A8 at http://www.ebay.com/sch/i.html?_nkw=jimb15122

Print Settings: Printer: Anet A8 Rafts: Doesn't Matter Supports: Yes Resolution: .1 Infill: 20 Post-Printing: Screw hole size I had to use a small file to make the holes slightly larger for the screws, allowing them to fit through without threading....

Anet A8 BLTouch Mount - Right Side - Inline with Nozzle There are a lot of Anet A8 3D Touch mounts out there, but none met my needs. I wanted the probe on the right side and inline with the nozzle, not in front or behind it. I designed this one, and...

This is a straightforward bowden motor mount for an Anet A8.\nAttaches to the top of the frame via two existing 3mm frame bolts, either left or right.\nThe other designs didn't seem sturdy enough with tabs to hold them securely in place or offered...

This set is cleverly designed and aesthetically pleasing due to its unique modules, inspiring me to create remixes that can be easily adapted to my ANet A8 printer. I've added an innovative touch by incorporating a Touch-Mi on the right side,...

The Z Axis threaded rod for the Anet A8 falls short of reaching all the way to the frame, causing z wobble. I designed this simple object to press fit onto the top of the rods, extending them enough to reach the holes in the frame. Installing them is...

I merged the Anet A8 LCD backplate with a fantastic Raspberry Pi case, positioning the Pi at the back where the camera ribbon can freely move without twisting. No extra parts are required if you're working with a standard Anet A8 setup. The...