general lee 3d models

My target scale for all source files and output STL files is 1:1000, However, I generally recommend 1:2500 or smaller given the detail level of the model. Although these files have not been extensively tested through printing, they are intended to...

The D1 mini will save and reboot, try to connect to the wifi (up to 30 times) generally after a few attempts it will connect, update the time and display it. The serial monitor shows a lot of what it's doing now so should help with...

For the first assembly (even if only in replacement of version 3.1 or 3.0 if you want), you have to couple and run in the thread (a bit like it happened in version 2.0 or in general) because it is very tight tolerance and to do so, if you have a...

Notes on scaling and working with Blender ----------------------------------------- My target scale for all source files and output STL files is 1:1000, However, I generally recommend 1:2500 or smaller given the detail level of the model. Although...

The valiant Auron is a second-generation Golem Simulacrum infused with the souls of ancient Golemmar generals. This massive Thorium Golem is a champion of justice and light. As he roamed Rotvar to fight against injustice and protect the helpless from...

All other parts and assemblies are original designs made specifically for this project! GENERAL PRINTING INSTRUCTIONSThis game was designed with FFF/FDM printers in mind. All parts used for testing were printed on a stock Prusa I3 MK3, without...

PLA is generally considered non-toxic, unless it is an exotic filament with strange additives. That being said, it is obviously inadvisable to use 3d-printed dishes or utensils because they are porous and can harbor bacteria. However, a knife block...

All in all, I believe your satisfaction with this mask should be limited only by the skill with which you make it, and not by any features of the design.Hope I won’t see any more comments to this design base on general 3d print issues(rough surface,...

TPU).GeneralIn any case print the handle with some sturdy material like PLA/PETG and the rubber with some flex material like TPU. When using the the default settings (no offsets) the rubber part should tightly fit into the handle. Since it's TPU you...

Notes on scaling and working with Blender ----------------------------------------- My target scale for all source files and output STL files is 1:1000, However, I generally recommend 1:2500 or smaller given the detail level of the model. Although...

  I went back and forth .1mm and finally decided on publishing a tighter tolerance first.  Please let me know your experience.  Tolerances are generally applied to the shaft HOLE and not the shaft.  This means you should be...

Also printed in PETG they have worked reliably for years.Usage of ClipsIn general, you should be able to just clip-on the clips to the M8 threaded rod. Check that it sits straight at the end. For me it works out just fine at least 9 out of 10 times...

Notes on scaling and working with Blender ----------------------------------------- My target scale for all source files and output STL files is 1:1000, However, I generally recommend 1:2500 or smaller given the detail level of the model. Although...

After that, sand it down and leave it for a few hours, you can generally tell if its set because just naturally it will feel smooth to the touch, sanding it again with some fine sandpaper before applying filler primer, and then finally spray paint...

Notes on scaling and working with Blender ----------------------------------------- My target scale for all source files and output STL files is 1:1000, However, I generally recommend 1:2500 or smaller given the detail level of the model. Although...

You can buy any glue / accelerator you want, I generally work with Akfix 705. Step 1 - Button / Button Housing Version 1 of my design had a printed "spring" that worked, but broke after repeated use. V2 removed the spring and I used the foam...

Whatever you have to add (or subtract as the case may be) to the average in order to get 180 (or 0 or 360) is the number you have to generally add (or subtract) to compass bearings to get true bearings. If you need to go the other way, i.e. convert...

For the part cooling side, the larger feed is pumped into a small nozzle aimed directly at the hot end's output, while the smaller feed is channeled around the front to a wider nozzle intended for general part cooling. This seems to strike a good...

Here's what to do:Before starting, make sure your printer is properly calibrated/homed.Printer Settings:GeneralTo start, create Three Separate Printer Setting Profiles. One profile for Left Extruder only, one profile for Right Extruder only, and one...

Here is a short instruction of how it works: I used Prusa Slicer for this but I guess it would work with the original Slic3r in a similar way Setting up Prusa Slicer In Prusa Slicer go to the "Printer Settings" tab. In the "Printer Settings" tab go...

You may want support on the Y-Axis part, I didn't on the part I used in assembly but it might help. Infill varies between parts, most were printed with 5%, the clips were 100%. Post-Printing Build & Assembly Notes: General: You may need to...

It is a great general area work light and performs well when used for outdoor illumination. The 140° beam offers a very wide lighting pattern and is ideal for situations where lighting distance is not a concern, but illumination of a wider area and...

If you would like to see my other designs, just search for "frimmel" at https://www.thingiverse.com. Please be aware that my designs are generally CC non-profit. Please respect this decision, as I constructed the objects and drew all the patterns...

Notes on scaling and working with Blender ----------------------------------------- My target scale for all source files and output STL files is 1:1000, However, I generally recommend 1:2500 or smaller given the detail level of the model. Although...

As in generally the first few seconds after changing colours usually does not print well ruining the top text (especially with PETG). You can preview the printing sequence in PrusaSlicer for the first layer to see where it will print first after...

Despite the general disagreement about this Mech’s efficiency, the author of Warhawk model for 3D printing decided to take up the project and spent 124 hours to create the famous assault giant with a huge torso and a nice arsenal of long-range...

VFA-6 variants are in general much more manoeuvrable, they have a large number of internally mounted short-range missile systems and can function on land, in the air, in space or underwater - Alpha can truly boast of total environmental...

although it is quite simple and intuitive. Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: No Supports: Yes Resolution: 0.4 Nozzle Infill: 10-15% Filament: Fillamentum PLA Traffic Black, Traffic White, Traffic Yellow, Vertigo...

Although this all built successfully for me, this is just a disclaimer that although I have some general background in this area I am a novice, so there is likely improvements that can be made to all areas of the design. In that regard I have also...

When choosing the tree for your 3D printed pot it is recommended that you take the following general rules into account: the pot’s depth should be equal to the diameter of the trunk just above soil level. For oval pots, the length of the pot...