general lee grill 3d models

Notes on scaling and working with Blender ----------------------------------------- My target scale for all source files and output STL files is 1:1000, However, I generally recommend 1:2500 or smaller given the detail level of the model. Although...

EEPROM autoinit on first boot after flash. -Homing feedrate tweaks -Z Safehoming enabled -Unified bed leveling enabled with finer 9x9 grid if you want to switch to a different method -- switch between mesh bl and ubl in config.h  -Detailed logging of...

After that, sand it down and leave it for a few hours, you can generally tell if its set because just naturally it will feel smooth to the touch, sanding it again with some fine sandpaper before applying filler primer, and then finally spray paint...

You can buy any glue / accelerator you want, I generally work with Akfix 705. Step 1 - Button / Button Housing Version 1 of my design had a printed "spring" that worked, but broke after repeated use. V2 removed the spring and I used the foam...

Although this all built successfully for me, this is just a disclaimer that although I have some general background in this area I am a novice, so there is likely improvements that can be made to all areas of the design. In that regard I have also...

In Sketchup, make sure not only Gamma is on but that textures were applied or imported in your current scene and now ready for high-quality image generation after just two clicks on export.Cinema 4D renders also benefit from same simple workflow of...

although it is quite simple and intuitive. Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: No Supports: Yes Resolution: 0.4 Nozzle Infill: 10-15% Filament: Fillamentum PLA Traffic Black, Traffic White, Traffic Yellow, Vertigo...

Notes on scaling and working with Blender ----------------------------------------- My target scale for all source files and output STL files is 1:1000, However, I generally recommend 1:2500 or smaller given the detail level of the model. Although...

Notes on scaling and working with Blender ----------------------------------------- My target scale for all source files and output STL files is 1:1000, However, I generally recommend 1:2500 or smaller given the detail level of the model. Although...

 Thankfully, you can iterate for a good fit with your printer by adjusting just one small part (the alignment ring) so you don't need to worry about having to throw away any big prints if they don't fit correctly on the first try.For general...

General approach is the same as for auto bed levelling with an inductive probe. As mentioned elsewhere the nozzle is the probe so offsets are x0,y0 z0.2 this is an approximate z offset which should leave the nozzle just above the bed at z=0, reduce...

It is a great general area work light and performs well when used for outdoor illumination. The 140° beam offers a very wide lighting pattern and is ideal for situations where lighting distance is not a concern, but illumination of a wider area and...

The magnets used for the hold-down are the same as I have used in other projects and their sourcing is specified in http://www.thingiverse.com/thing:77734. The photos show what sorts of components I have used - generally widely available - and how...

Here's what to do:Before starting, make sure your printer is properly calibrated/homed.Printer Settings:GeneralTo start, create Three Separate Printer Setting Profiles. One profile for Left Extruder only, one profile for Right Extruder only, and one...

Notes on scaling and working with Blender ----------------------------------------- My target scale for all source files and output STL files is 1:1000, However, I generally recommend 1:2500 or smaller given the detail level of the model. Although...

Notes on scaling and working with Blender ----------------------------------------- My target scale for all source files and output STL files is 1:1000, However, I generally recommend 1:2500 or smaller given the detail level of the model. Although...

Notes on scaling and working with Blender ----------------------------------------- My target scale for all source files and output STL files is 1:1000, However, I generally recommend 1:2500 or smaller given the detail level of the model. Although...

Files: • CarriageV3.stl (carriage base, minus blower mount) • LimitSwitchPlate.stl (striker plate for x-axis limit switch) • PCBstandoff.stl (Qidi printed circuit board mount) • BeltClamp.stl (x-axis belt clamp) • CableGuide.stl (flex cable routing...

  I went back and forth .1mm and finally decided on publishing a tighter tolerance first.  Please let me know your experience.  Tolerances are generally applied to the shaft HOLE and not the shaft.  This means you should be...

All in all, I believe your satisfaction with this mask should be limited only by the skill with which you make it, and not by any features of the design.Hope I won’t see any more comments to this design base on general 3d print issues(rough surface,...

Here is a short instruction of how it works: I used Prusa Slicer for this but I guess it would work with the original Slic3r in a similar way Setting up Prusa Slicer In Prusa Slicer go to the "Printer Settings" tab. In the "Printer Settings" tab go...

The motion of the Slide moves the Hammer via small bosses in the Slide, keeping the Rotor free to turn. The Rotor is the square notch style from the bakewell remix, to which I added a flange on both sides to keep it centered in the Slide. Changed the...

Assuming I did my math right you will generally want to start with about 40-50mm of exposed inner slide and tune from there. Now cut a 16” long piece3 of the same ½” schedule 40 PVC pipe and fit it into one side of the tuning slide inner mount. Fit...

All other parts and assemblies are original designs made specifically for this project! GENERAL PRINTING INSTRUCTIONSThis game was designed with FFF/FDM printers in mind. All parts used for testing were printed on a stock Prusa I3 MK3, without...

For the part cooling side, the larger feed is pumped into a small nozzle aimed directly at the hot end's output, while the smaller feed is channeled around the front to a wider nozzle intended for general part cooling. This seems to strike a good...

Current version is not compatible with the landing gear that is created and is being tested GENERAL State Simple version Nozzle 0.4 mm Layer height 0.2 mm Shells 2 or 3 Supports none Material PLA or PETG Multi color print yes Colors...

Also printed in PETG they have worked reliably for years.Usage of ClipsIn general, you should be able to just clip-on the clips to the M8 threaded rod. Check that it sits straight at the end. For me it works out just fine at least 9 out of 10 times...

My target scale for all source files and output STL files is 1:1000, However, I generally recommend 1:2500 or smaller given the detail level of the model. Although these files have not been extensively tested through printing, they are intended to...

Notes on scaling and working with Blender ----------------------------------------- My target scale for all source files and output STL files is 1:1000, However, I generally recommend 1:2500 or smaller given the detail level of the model. Although...

 I didn’t design this with the general population in mind and to be “IKEA” simple, but with that said, placing the holes is probably the most challenging part since that can take some precision and bit of thought.  I have tried to describe things the...