general electric f101 3d models

PLA is generally considered non-toxic, unless it is an exotic filament with strange additives. That being said, it is obviously inadvisable to use 3d-printed dishes or utensils because they are porous and can harbor bacteria. However, a knife block...

  I went back and forth .1mm and finally decided on publishing a tighter tolerance first.  Please let me know your experience.  Tolerances are generally applied to the shaft HOLE and not the shaft.  This means you should be...

Notes on scaling and working with Blender ----------------------------------------- My target scale for all source files and output STL files is 1:1000, However, I generally recommend 1:2500 or smaller given the detail level of the model. Although...

As in generally the first few seconds after changing colours usually does not print well ruining the top text (especially with PETG). You can preview the printing sequence in PrusaSlicer for the first layer to see where it will print first after...

Notes on scaling and working with Blender ----------------------------------------- My target scale for all source files and output STL files is 1:1000, However, I generally recommend 1:2500 or smaller given the detail level of the model. Although...

You may want support on the Y-Axis part, I didn't on the part I used in assembly but it might help. Infill varies between parts, most were printed with 5%, the clips were 100%. Post-Printing Build & Assembly Notes: General: You may need to...

Here is a short instruction of how it works: I used Prusa Slicer for this but I guess it would work with the original Slic3r in a similar way Setting up Prusa Slicer In Prusa Slicer go to the "Printer Settings" tab. In the "Printer Settings" tab go...

Files: • CarriageV3.stl (carriage base, minus blower mount) • LimitSwitchPlate.stl (striker plate for x-axis limit switch) • PCBstandoff.stl (Qidi printed circuit board mount) • BeltClamp.stl (x-axis belt clamp) • CableGuide.stl (flex cable routing...

Notes on scaling and working with Blender ----------------------------------------- My target scale for all source files and output STL files is 1:1000, However, I generally recommend 1:2500 or smaller given the detail level of the model. Although...

They also give you an exact 1:1 ratio between the control horn and servo horn which is generally ideal for good aerobatic throws while using the entirety of your radio system's extended limits. Using the full CRSF range of values, -120 to 120 %...

You can buy any glue / accelerator you want, I generally work with Akfix 705. Step 1 - Button / Button Housing Version 1 of my design had a printed "spring" that worked, but broke after repeated use. V2 removed the spring and I used the foam...

My target scale for all source files and output STL files is 1:1000, However, I generally recommend 1:2500 or smaller given the detail level of the model. Although these files have not been extensively tested through printing, they are intended to...

general cleanup (converted tabs to spaces + correct indentation) on different files 2. restored slovenian language in config.ini file (it was removed by mistake in the last BTT merge) 3. changed some label names (e.g. ABL_start) whose values...

TPU).GeneralIn any case print the handle with some sturdy material like PLA/PETG and the rubber with some flex material like TPU. When using the the default settings (no offsets) the rubber part should tightly fit into the handle. Since it's TPU you...

Do it.Once I felt good about their general operational level, I added 2 or 3 layers of teflon tape to the threads. This serves two purposes: first, it makes them operate a lot smoother and second it tightens up the tolerances. by adding another and...

Here's what to do:Before starting, make sure your printer is properly calibrated/homed.Printer Settings:GeneralTo start, create Three Separate Printer Setting Profiles. One profile for Left Extruder only, one profile for Right Extruder only, and one...

Notes on scaling and working with Blender ----------------------------------------- My target scale for all source files and output STL files is 1:1000, However, I generally recommend 1:2500 or smaller given the detail level of the model. Although...

Same considerations made for the upper shroud about the number of perimeters to be set. Requirements Upper Z-VENT 1x radial fan 40x40x10. 3x M3x12mm button head or socket head cap screws. 3x M2.5x6mm screws (no flat head type) or 3x 2.2x6mm self...

Plus, the longer rudder can help with general maneuvering. I thought a slip-on conversion would allow anyone to try the new rudder without permanent modification and make future design changes easy to implement. Further, I wanted to keep the stock...

Whatever you have to add (or subtract as the case may be) to the average in order to get 180 (or 0 or 360) is the number you have to generally add (or subtract) to compass bearings to get true bearings. If you need to go the other way, i.e. convert...

Notes on scaling and working with Blender ----------------------------------------- My target scale for all source files and output STL files is 1:1000, However, I generally recommend 1:2500 or smaller given the detail level of the model. Although...

All in all, I believe your satisfaction with this mask should be limited only by the skill with which you make it, and not by any features of the design.Hope I won’t see any more comments to this design base on general 3d print issues(rough surface,...

Notes on scaling and working with Blender ----------------------------------------- My target scale for all source files and output STL files is 1:1000, However, I generally recommend 1:2500 or smaller given the detail level of the model. Although...

EEPROM autoinit on first boot after flash. -Homing feedrate tweaks -Z Safehoming enabled -Unified bed leveling enabled with finer 9x9 grid if you want to switch to a different method -- switch between mesh bl and ubl in config.h  -Detailed logging of...

Despite the general disagreement about this Mech’s efficiency, the author of Warhawk model for 3D printing decided to take up the project and spent 124 hours to create the famous assault giant with a huge torso and a nice arsenal of long-range...

VFA-6 variants are in general much more manoeuvrable, they have a large number of internally mounted short-range missile systems and can function on land, in the air, in space or underwater - Alpha can truly boast of total environmental...

When choosing the tree for your 3D printed pot it is recommended that you take the following general rules into account: the pot’s depth should be equal to the diameter of the trunk just above soil level. For oval pots, the length of the pot...

Current version is not compatible with the landing gear that is created and is being tested GENERAL State Simple version Nozzle 0.4 mm Layer height 0.2 mm Shells 2 or 3 Supports none Material PLA or PETG Multi color print yes Colors...

Claptrap is a CL4P-TP general purpose robot manufactured by Hyperion and has been programmed with an overenthusiastic personality. It brags frequently, yet also expresses severe loneliness and cowardice.ADAPTATION FOR 3D PRINTINGClaptrap for 3D...

The blast can also be used, generally under extenuating circumstances, with just one arm or even the feet. ABOUT THIS 3D FIGURINEThe model is saved in STL files, a format supported by most 3D printers. FDM version features:- Contain 17 parts;- Made...