gen 1 starters evolutions 3d models

This is my take on a mount for the Orbiter 1.5 with the Hero Me Gen 5 for my Ender 5. This is a work in progress as i missed the hole behind the extruder ( included in this file ) but i haven't printed it again. The orbiter i got from Amazon was a...

For MKS GEN 1.4 boards, print BASE_MKS_GEN_1_4.stl and LEFT_MKS_GEN_1_4.stl OR For RAMPS 1.4 boards, print BASE_RAMPS_1_4.stl and LEFT_RAMPS_1_4.stl OR For any other boards print BASE_UNIVERSAL_MOUNT.stl and BASE_UNIVERSAL_MOUNT_SCREWHOLES.stl and...

This part enables the installation of an MKS Gen 1.4 in place of the stock GT2560 on a Geeetech i3. I'm using an i3 Pro B, but this design should also work with other similar GeeeTech printers - if so, please add your comments to inform others! ...

For the right side, I adjusted the USB port cutout and removed the SD card slot to suit the MKS Gen L v2.1. An additional cutout was added for routing the bed, x-axis and hot end cable bundles out the back instead of the top cover. I found this made...

This is a remix from Yaan's MKS Gen 1.4 Case, which was itself a remix. I repositioned the M6 holes to mount 3030 extrusion on the outside of the case instead of inside. This way, your X stepper won't collide with the case if you attach it to the...

MKS GEN-L V2.1 & Lerdge MOS case 材料清单4个M3×12 螺丝4个M3 螺母8个M3×8 螺丝4个M3×40 螺丝2个M4×10 螺丝2个M4 T型螺母  Bill of materials4 units M3×12 screws4 units M3 nuts8 units M3×8 screws4 units M3×40 screws2 units M4×10 screws2 units M4 T nutsMKS...

I created these plans for a gen 1.4 MKS and I aimed to design a drawing as light as possible, so here I have a printer in 24V and only fans at 12V. So, I decided to make this remix so it can be used with old fans recovered. And I connected them in...

EN: Hello I made these plans for a gen 1.4 mks and I tried to make a drawing as light as possible so here I have a printer in 24v and only fans in 12v so I decided to make this remix to be able used old fans recovered. ...And I connected them in series...

This mount adapts MKS GEN 1.4 to 2040 aluminum extrusion. I built this with Bear Upgrade in mind, but it should also mount anywhere. ...This mount also provides means of attaching two 5x7cm daughter boards at the back, cable management for the extruder,...

It also fits the MKS GEN-L and the newly released SKR 1.3 board. The hole distance is 101.85 x 76.10mm. To mount the board, I use 4pcs M3x16mm screws and M3 nuts. The extrusion mounting holes are 6mm wide and 5mm deep for M5 screws (x8 or x10mm). ... |...

I have been setting up to install Hero Me Gen 5 cooling system on my Ender 3 Pro, but spotted a couple inconsistencies in the documentation when choosing an extruder adapter: 1) I had an "all-metal" Creality upgraded extruder, which is not the OEM...

This adapter enables a seamless transition between a standard shop vacuum and the 80% Arms Easy Jig Gen 2, allowing for efficient use of both tools in various projects.

Hi everyone, I came across this incredible Design by KerseyFabrications that houses the MKS Gen 1.4, the MOSFET and the raspberry pi and really wanted to use this design. Unlike him, I utilize the Trinamic TMC 2130 stepper drivers which are taller...

This remix will work for MKS GEN 1.4. The case and lcd are remixed, the other parts are available on original thing (https://www.thingiverse.com/thing:516447). Also this remix have four nuts inside the case to let you mount the case on a...

I designed this case to fit perfectly on the side of my Anet A8 and securely hold a MKS Gen V1.4 mainboard, Raspberry Pi 3, and a MOSFET for the heatbed. Hardware: * 8 M3 Nuts * 8 M3 Washers (Recommended) * 8 M3 x 12 Screws * 4 M2 Nuts * 4 M2...

I created this case to mount on the side of my Anet A8 and hold a MKS Gen V1.4 mainboard, Raspberry Pi 3, and a MOSFET for the heatbed. Hardware: * 8 * M3 Nuts * 8 * M3 Washers (Recommended) * 8 * M3 x 12 Screws * 4 * M2 Nuts * 4 * M2 Washers...

This only includes the SKR 1.3/MKS Gen L half with the extra posts for two more buck converters. ...The rest of the parts can be found in the Ender 3 all in one, universal rear electronics case Thing by Teaching Tech at <a...

The output of "the Orbiter" is a little off center from the Hot End input, because the MDD 1.3's extruder mounting holes are the same distance as those in the housing mount for "The Orbiter" This is my first attempt in years to use CAD or design...

I made a Prusa i3 mk3 Clone with a MKS Gen L as the mainboard, so I needed a case for it (should also work with an SKR board - I did not test it though). It can contain TMC2130 in SPI with the pins directed upwards. There's plenty of clearance for...

Dropped - where the SKR 1.3 board is lowered by 10mm vertically - this eliminates the tight bend the USB extension cable makes at the top; there's a left and right version or swap them to raise the controller board by 10mm. Each variant comes in a...

But it's definitely the best case to use for the SKR 1.3 and the MKS Gen L boards. UPDATED: 05/28/2019 A few people have commented on how tight the print fits on the Ender 3 printer. Yes, it's a tight print and if you don't have your printer dialed...

It lacks finesse (no fillets on the rectangular hole, and it is also about 1-1.5mm higher than it could be), but it fits perfectly. If someone wants to polish it and add all the niceties, dm me and I will get you a tinkercad link. Putting this up in...

It took a lot of measuring to get it right, but this case is now the go-to choice for SKR 1.3 and MKS Gen L boards. UPDATE: Some users have pointed out how snugly the print fits on the Ender 3 printer. Yes, it's a tight fit, and if your printer...

I've had some requests for the base plate and top cover for the Ender 2 printer to fit the SKR 1.3 and MKS Gen L boards. Here you go. Print the top cover with the front face facing downward on the bed. and you shouldn't need supports for the USB and...

+UPDATE V0.67 19/3/19 - Added Support for Raspberry Pi 3B+/3B/B+ +Bugfix V0.67 22/3/19 - Some holes of the Dual_mosfet_supp were missing +Bugfix V0.68 25/3/19 - All holes have been changed +0.5 mm of space - Rasbperry hole fixed +UPDATE V0.68...

We'll focus on bugfixes and a new section "UPDATE IDEAS" for increased compatibility with more boards and printers, Thanks to all supporters!\r\n\r\n+UPDATE V0.67 19/3/19\r\n- Added Support for Raspberry Pi 3B+/3B/B+\r\n\r\n+Bugfix V0.67 22/3/19\r\n-...

Here's My Design for the Ender 3 Pro: A Comprehensive Upgrade Guide If you're planning to upgrade your controller board on the Ender 3 Pro, this design is specifically tailored for the SKR 1.3 or MKS Gen L boards. While it should also work seamlessly...

Box to hold the MKS Gen .4- Space for a 60mm fan to cooldown the drivers (I use TMC2208)- Holder for 2 LM2596S stepdowns (for hotend fan and driver cooldown)- Cable guides for gantry and powerBOM:- 10mm M4 screw x 15- M4 screw insert x 15- M3 10mm...

Adapter Bracket for Seamless Mainboard Swap Replace the Wanhao/Cocoon Create Plus motherboard with ease using this adapter bracket, specifically designed for a MKS Gen/Base V1.4 upgrade. No External Holes? No Problem! ...Although external connector...

Gotta love me some Chimchar! 2 adorable poses, showing off his Monkey mentality! Make sure to check out my other models, as well as my "Chimchar Unleashed" figure! ... *If you want to sell your prints of this model, please subscribe to a merchant tier...