geeetech a20 3d models

I remixed this item to fit my geeetech A20.

... * 5015 fan * 2 M3x25 screws Print the duct with the large side facing downwards towards the buildplate. Inspired by Thingiverse's design: https://www.thingiverse.com/thing:3435671, but modified to fit the Geeetech A20 printer's smaller dimensions.

These are some tries to upgrade stock fan duct of my GA20. ... Any suggestion will be very appreciate. Printed with Geeetech A20 Geeetech PLA purple Layer **0.2mm** HeadTemp: **200°C** BedTemp: **50°C**

I made this adapter because the original knobs of the geeetech a20 are too small and not very precise. Attention! ...the knob behind the left must remain small due to collision with the Y stepper!

I made this adapter because the original knobs of the geeetech a20 are too small and not very precise. Attention! ...the knob behind the left must remain small due to collision with the Y stepper!

Better fan for the Geeetech A20(M)Parts needed:-5015 fan-2x M3x25Print the duct with the large side facing the buildplate.

Geeetech a20(m) Screen Cover

Satsana modified for Geeetech A20 with the wall to mount the board

... demanding applications. ...Its sturdy construction ensures reliable operation, even under intense usage. The sleek design seamlessly integrates into the Geeetech A20/A20M 3D printer, providing users with enhanced printing performance and efficiency.

Geeetech A20 bed leveling knobs. Simply print and plug it over the original black one. --- I suggest to print the TEST stl to check how it fit. If needed up or down scaling a bit then test again. ... Enyoj!

Fan duct it's a replacement for Geeetech A10 and A20. ...It need supports only from the bed.

This system use the original 40x40 radial fan duct, but pay attention, my A20 is not completely original: I wanted to adjust the fan speed (small parts, slow parts, surfaces,bridges ecc..), but with the original firmware I only had the ON / OFF...

Original fan duct for 5015 fan on Geeetech A20

Support for the Z-axis bearing on the Geeetech A20 is now available.

filament sensor guide and support for geeetech a20 use a 62608 bearing and M5 and stock screw

Here is the rewritten text: Geeetech A20 Filament Sensor Installation Guide and Support To assemble the Geeetech A20 filament sensor, follow these steps: Use a high-quality 62608 bearing and M5 screws to ensure smooth operation. ... Install the bearing...

I rapidly cobbled together a mounting system for the Microsoft Lifecam HD3000 to integrate with my Geeetech A20 printer, utilizing Octoprint functionality. ...This makeshift solution might also be compatible with the Geetech A30 model; however, I do not...

Modification for Geeetech A20 printer. This custom support replaces the original flawed model that frequently breaks the fastening slot of the micro filament sensor. By switching to this support, the filament moves along a more secure path, avoiding...

Remixed from Geeetech A20 120mm fan conversion and riser legs by Splund March 28, 2020 https://www.thingiverse.com/thing:4246677 I wanted to use one leg as mount for my PS Eye Cam for Octoprint Video. ... You can use any top part and i used: PS3 Eye...

The Geeetech A20 (at least my version) has an external MOSFET which has a 25x25mm fan on it which hardly moves any air - therefore I decided to go one step further and mount a 30x30x10 fan (USONGSHINE 24V DC 303010). Any other manufacturer fan should...

As there was no attachment for a cable chain for the Geeetech A20 hotend I designed a simple one. If you decide to print please make sure to rotate it 180° in the x or y axis, otherwise you will have a mess of supports (which this part needs). For...

I was very annoyed with the loud hotend cooler fan of the Geeetech A20 and decided to replace it with a bigger fan which is more quiet. The fan has dimensions of 40x40x20 and is mounted on the side of the hotend cage. For mounting the adapter to...

... GPIO pins. 9. Cut and crimp a USB cable with a JST-XH connector, and connect it to the Pi and controller board. 10. Power on the printer, and done! You should see a /dev/ttyUSB0 which can be used by OctoPrint or Klipper. Geeetech A20 A20M A20T

# *>>NEW VERSION AVAILABLE https://www.thingiverse.com/thing:5170055 This is a optimized version of the fan duct for the stock A20 fan, maybe it is suitable for the other Geeetech printers (A10, A20M, A30), if you try it let me know. It is more...

Mount for ataching a 3d touch / BL touch to the side of the A20 X carrage.

... ... This is a remix from https://www.thingiverse.com/thing:4738946/files. You can use the chain from johnniewhiskey https://www.thingiverse.com/thing:2920060 It works perfekt at my A20. ... Maybe it works on other Printers with the V4 Extension Board

... is a remix from https://www.thingiverse.com/thing:4738946/files. You can use the chain from johnniewhiskey https://www.thingiverse.com/thing:2920060 It works perfekt at my A20. ... Maybe it works on other Printers with the V4 Extension Board

I remixed it to fit the LCD on my Geeetech A20M.

The design should work for both A10/A20 and A10M/A20M models, but you'll have to confirm that for me. To start, I upgraded the hotend cooling fans to 40x40x20mm (24V) versions available on Amazon. I also swapped out the part cooling blower with a...

I remixed this from https://www.thingiverse.com/thing:4255972 Changes I made: - Duct 1 mm higher (I've had some trouble with the duct hitting the prints) - Smaller Duct (stay away from the extruder) I remixed it with fusion 360, you'll find...