geebee r1 3d models

Adjustable Z rod stabilizers for the ROBO R1 model. Mount these stabilizers inside the plastic hood using double-sided tape or double-sided adhesive pads. Two small M3 bolts are required, specifically an M3 bolt measuring 20 mm in length and...

Yet another GoPro bed mount for the R1+. I wanted to be able to place the mount either left, right, or centre, as well as print with less material and fewer/no supports. There are two versions: one for right-handed knob placement, and one for...

... I wanted. I used this LED; https://alofthobbies.com/led-lights-5822.html?___SID=S Print Settings Printer Brand: Robo 3D Printer: R1 ABS + PLA Model Rafts: None Needed Supports: Not Necessary Resolution: High at .2mm Infill: Lightly filled at 20%

Wanted 30mm hot end fan mount for my R1+. New to this, so I just had a little fun with it. Works good. Will need a longer screw for the X limit switch. I flipped the fan to pull through instead of push. ...Works much better and doesn't bog the fan...

This is a replacement power "button" for an Onkyo R1 CD player. The original button is a bizarre and fragile contraption. This one is a bit beefier. To install it, removed the little circuit board that's attached to the actual switch. Slide the...

When my Robo3D R1 arrived, I discovered a cracked spare part in the box, but fortunately it included an extra one for emergencies like this. My first priority was to print and clean this critical component before using it. ... Instructions Print the Y...

The Y-axis belt block is a crucial component that secures the Y-axis belt to the bed frame of my Robo3D R1 printer. Fortunately, it arrived with a spare unit, which I was able to use as a backup after discovering that the original one had cracked. ...To...

Idea is to get a quite cheap, but fast car.Manufacturing started yesterday - hope to hear the engine (Yamaha R1 - 183hp) scream before April.Current development time about 6 weeks.If u want to stay up to date you can visit:...

I took the Wade extruder file from http://www.thingiverse.com/thing:729956, and modified it to fit the R1+ quick release hotend, as well as to include a separate filament path with a Y-junction inside the part. I'm hoping to make a similar setup to...

Here are a couple of fan shrouds mashed together to improve airflow dispersal around my Robo R1 Plus hot end. Prints in one piece and fits a 40mm fan, clipping onto the back of the x-axis carriage. ...(It may also fit on the front of the x-axis...

Needed few changes to increase strength and retentionBattery Clips for Toshiba Portégé R830 R1.My son knocked both of them out and only managed to find one of them. I measured it an modeled it strengthen it a bit, mirrored it and printed. ...I installed...

Z-axis lead screw adapter for the Robo 3D R1: Print Settings: Rafts: Yes The use of a raft helps with first layer adhesion. Raft width and thickness may need to be adjusted for this specific print. Supports: ...

Another GoPro bed mount for the R1+, designed to offer flexibility in placement and minimal material usage, with two versions available - one suited for right-handed knob placement and another for left-handed users. ... Recommended accessories include...

Spool holder for Robo 3D R1 inspired by the original design. This accessory adapts seamlessly to the upper portion of the casing and is incredibly simple to install, providing maximum stability and support in the process. It streamlines the...

Tapacubos protector for Ride R1 rear parts. They fit with relative ease. ...Apply glue both before and after to ride without fear of tearing the flank.\nMin 5:30 in this URL:\nhttps://www.youtube.com/watch?v=CGfFE2kfzpY\nThanks\nPrint Settings\nPrinter:...

A friend of mine was missing the R1 and L1 buttons on their Playstation 3 controller, so I decided to design and print new ones instead of buying a replacement. My custom design works perfectly, and I'm excited to share it with you. Feel free to...

Spent quality time reviewing the original Robo 3D-provided R1 extruder file to remove all injection molding scallops as well as eliminate the screw-mount holes for the extruder, and update the inside of the base to work seamlessly with the R1+...

Can Reduce Drive temps by 7-12C Clip-on on non-permanent attachment, does not require any modification to the R1/R7Uses (8) standard PC case fan screwsLow Profile / Sleek design does not change the overall look and feel of the R1/R7 and has minimal...

Please note that Orange Pi R1 Plus is different and the USB-A / USB-C are swapped in location. ## Changes * Enclosed SD card and reset button. Case is a little wider and deeper to facilitate this. * Redid openings for ethernet/usb to make...

This is made to fit onto the stock Robo3d R1+ bracket with a snug press fit. From there you can run one chain to the x-carriage and another down the z-axis for a sleek look. ...Design to use this chain: http://www.thingiverse.com/thing:1580776 Works...

I have prepared updated version of the mounting plate for Voron Afterburner R1. It fits only Ender 3 Pro. ...It has additional hole for heat insert to mount Bltouch.</p><h3>Print Settings</h3><p><strong>Printer Brand:...

With the Robo 3D R1 Camera Mount, users can attach cameras designed to sit atop monitors to achieve unique perspectives in their prints. ...The design includes three distinct models: one standard model that allows the camera to be positioned as shown...

High-resolution model of the Yamaha R1 (2015) motorcycle made completely in Blender comes with every necessary detail including textures and decals for the front fender and the dashboard where every switch is clearly defined with detailed decals. ...If...

A vital accessory for the Robo 3D R1 Plus, Z-bar braces are engineered to stabilize the Z-axis bars/threaded rods, and to significantly reduce vibration when used with optional vibration dampers. Specifically designed for use with a robust 608ZZ...

This is the stabilizer I built for my Robo 3D R1. Since you're using Z rods that extend to the top of your case, this setup might not work as intended if you have a different model - in which case additional modifications would be necessary. The...

This carriage easily connects the Titan Aero extruder to the Robo 3D R1 printer. Print it with supports, but note that v3 can be printed without them. I made mine using PETG filament. The two attached pictures show modified versions that secure...

I'm adjusting the settings for Robot IRB 120's connector R1.CP/CS to work seamlessly with its Prusa Steel printer. The print settings are as follows: Printer Brand is Prusa, and the specific printer model is also Prusa Steel. I've made sure there...

This is a remix of the Crosman 1377 suppressor V2 made by Thorium- specifically designed for the Crosman R1 air rifle. Note that this design will not fit earlier Crosman DPMS or Bushmaster air rifles due to different barrel threading. Printing...

I'm obsessed with giving my Robo 3D a sleek, high-tech makeover, but I know it needs a lot more than just a fresh coat of paint - it's got a glaring design flaw that screams for attention.\nPrint Settings\nPrinter Brand: \n Robo 3D\n \n Printer: \n...

This revised mount is designed specifically for use with the R1+ and its accompanying Hexagon hot-end. Originally, the fan shroud's design would cause it to make contact with the nozzle before the print could begin, rendering printing impossible. To...