garmin varia saddle rail mount 3d models

I just created a simple mount that lets me move my Garmin Nuvi from my windshield in seconds. Honestly, I really dislike having my view obstructed by it, and glancing down at the map is no more effort than looking elsewhere. Plus, with five cup...

I already had a Garmin GPS and friction dash mount. I move them between vehicles to a more permanent wiring solution to the top of the windshield is not an option. In some US states, you cannot have anything attached to your windshield, so putting...

... ABS is recommended for printing. Check out my bar mount for similar GPS devices. An update from 2015-09-29 offers a dashboard mount specifically designed for older eTrex Cx/HCx Vista/Legend series Garmin outdoor GPS units (available here).

With this mount you can use your edge and your UT800 headlight the same time with only one garmin mount. Print Settings Printer Brand: Wanhao Printer: Duplicator 6Rafts: Yes Supports: YesResolution: 0.2 Infill: 50 Filament: extrudr ABS black ...

Remixed from Pemlik's Handlebar mount for Forerunner 945, this thing allows you to attach your Garmin Forerunner 935 or Forerunner 945 with a Garmin Quarter-turn mount adapter. I adapted the back to fit this piece so you can attach it to your mount...

I created this so I could mount my Garmin where I wanted on my Giant Trinity Advanced bicycle which has an integrated water bottle that blocks most mounts. Positive and negative HEIGHT values let you position the mount to be even with the top of...

This design is remixed from dorsch's original Moto X Garmin Windshield Mount available at https://www.thingiverse.com/thing:263310. Initially, I discovered dosch's mount and printed it out, only to realize that it didn't fit my Moto X PURE, which...

Remixed from dorsch's Moto X Garmin Windshield Mount https://www.thingiverse.com/thing:263310 . I found dosch's mount and printed it, only to discover that it didn't fit my Moto X PURE, which is wider by about 10mm, so I modified it and the new...

I printed it horizontally, but the tabs in the Gamin mount could separate the print layer if your Garmin mount fits too tight* *** I've uploaded a new version with 1.3mm thick tabs (instead of 1.5mm), that should solve the issue. I broke the...

Remove velcro strap from Sony Live Remote Version 1 or 2 and slide tabs into mounting system slots on Garmin Quarter-Turn Mounting System. The remote unit clicks securely in place, no additional hardware needed. To Install: Snap off the Sony Live...

Garmin Approach Golf GPS units come standard with a belt clip, but I opt for a push cart mount instead. The belt clip does an excellent job of securing the GPS, so I designed a simple push cart mount to hold it in place. This setup is effortless to...

This is a custom mount for a Garmin CV52HW-TM Transducer. The mount was engineered to be used in conjunction with a Borika Universal Lock and Mounting Site, as seen in the accompanying images of the packaging and product. I affixed the mount...

The problem was that he only had the camera itself, without any protective case or mount, so I needed to come up with a solution to attach it to his standard tripod. ...Luckily, the design worked perfectly - the piece simply clips right on and has been...

Hello Everyone, I'm excited to share a DIY project that enables you to use your Garmin Etrex with a quarter-turn mount. Special thanks go to pbegala87 for creating the original design, which I've built upon by adding a cutout that allows easy access...

Garmin ZUMO XT Dummy for the Touratech Mount. adapted it and removed the cutout for the stock rubber contact protection . wich was not needed since its protected from weather by the dummy itself . also cleaned up how it attaches to the charging...

Suddenly, I recalled something I had spotted earlier called Hide My Bell, which is essentially a Garmin mount with an integrated bell. That got my creative juices flowing - I had the sudden urge to craft a GoPro mount that could also accommodate this...

Garmin/Sigma Rox 11 mount above stem Again another Gramin / Sigma Rox 11 mount for a handlebar diameter of 31.8mm. I Designed this for my own needs (fits perfect over a canyon v12 stem) so i hope it fits for you. It's easy to Print but needs some...

This adapter enables the suction-cup GPS mount on a Garmin GPS to securely attach to the smooth surface of the dashboard on the left side of the steering wheel. It's positioned right in front of the side window defrosting vent. First, adhere the GPS...

This will work with Garmin or GoPro. ...Holds pretty good, but WIP at this time.

I designed three bicycle mounts for a Garmin Fenix 5x watch, keeping things practical rather than fancy. The designs are based on a simple yet effective geometry. Version "steerer cap mount" replaces the topcap on your steerer or stem with a M6...

this piece clips right on and works. Made for Garmin VIRB Ultra 30 If you like what you are seeing, please consider following me. prusaprinters.org/frankdeschner/ There will be more practical #3dp prints regularly. Print instructionsPrinter:...

double rail mount.stl

Simple DIN rail mount

This car GPS mount is specifically crafted for Garmin 610 models, as well as others that share similar dimensions. Its primary function is to keep the device discreetly out of view beneath the dashboard in a Seat Leon 5F with its curved design. ...The...

You'll need to print the mount and a thumb screw(used to make sure the GPS does not fall out during off-roading) I used rubber grommets under the mount to dampen vibrations and also to raise it up. I used PLA but I think PETG or ABS would be a...

This model is based on the original dimensions of the factory mount but adds 25mm to the stem to allow my Garmin 1000 to fit snugly perfectly. The actual mounting disc is made with thicker tabs for additional strength and support when the unit is...

To solve this issue, I created a custom Trelock mount that fits onto the Garmin mount. This new design gives me full control over the light's positioning, making it easy to adjust left-right and up-down. The four parts of the mount slide together...

... This model is based on the original dimensions of the factory mount, but adds 25mm to the stem to allow my Garmin 1000 to fit snugly. The actual mounting disc is made with thicker tabs for additional strength and support when the unit is locked in.

I needed a way to mount my transom-mounted garmin strike transducer to my new Old Town Sportsman 120 PDL kayak. I found a few designs here that I was able to quickly munge up to make a specific part. I used the profile of the base/mount from...

... weather when I used it on another bike. I'm planning to add a charging port to this mount so I can utilize the Garmin Zumo mount's 5v charger and connect it to a USB embedded in this clip/mount. ... https://www.amazon.co.uk/gp/product/B01FQTB2MY/