garmin cable saver 3d models

Securely lock it into position with two sturdy M3x25 screws that effortlessly clasp onto the device's sleek housing, safeguarding its cable from potential damage or tangles. ...I apologize for the poor photo resolution used to demonstrate this...

... useful. ... This is a temporary fix that helps to hold in place the rubber part so that the cable is not strained. ...I will probably glue it carefully with some epoxy and use the 3d printed part to hold it in place as well as the epoxy cures.

This is V" of a previous design with room to remove the sd card given the location of my ender 3 V2 and how i use it the usb cable and micro usb port were practically susceptible to damage either from accidental knocking or repeated use so i designed...

This is V" of a previous design with room to remove the sd card given the location of my ender 3 V2 and how i use it the usb cable and micro usb port were practically susceptible to damage either from accidental knocking or repeated use so i designed...

They just fit but they can't be too long or you will hit the smooth rods. This is just a wedge with a little groove in the middle to angle the cable a bit. I fastened mine with 1 small zip tie.</strong></p> How I Designed This</h3> <p>I used my...

This is V" of a previous design with room to remove the sd card given the location of my ender 3 V2 and how i use it the usb cable and micro usb port were practically susceptible to damage either from accidental knocking or repeated use so i designed...

I wasn't able to find a 90 degree angle cable saver, so I sat down and designed one in FreeCad. FreeCad is parametric and I included my file for it. So you should be able to load it and go to the PART Workbench and make changes if you want to. ... I...

This is a DIY Lefty Cannondale cable saver designed to shield your fork from cables. It's essentially identical to the original Cannondale one. I created this version using filaflex and it performs flawlessly! I made mine by measuring my 2012 Lefty...

Looks great, exactly what I had in mind! Version 2.0 takes it up another notch with an even sleeker look. By the way, did you notice the nozzle size is set to 0.25 and the print speed is a brisk 40 mm/s? I'm also running a full infill percentage for...

The modified Human device has been successfully reconfigured to eliminate the unnecessary branding and optimized for seamless integration with conventional USB connectors. ...Its sleek new design ensures effortless compatibility with a wide range of...

This design was crafted entirely within Tinkercad. ...Make adjustments directly on their website at https://www.tinkercad.com/things/0bGOUeB878E.

My Masterclass printer has a problem; the wire wrap and tubing gets snagged on the track in one of the posts when it sets the head after completing a print job. So, this is a orb you secure to the wire wrap to stop that from occurring. You need to...

Does your iPhone cord keep snapping and getting eaten away? Print one of these today to start saving money on phone chargers! ... Print Settings Printer Brand: RepRap Printer: Prusa-i3 Rafts: It doesn't matter Supports: No Resolution: 0.2 mm Infill:...

This is a crucial component designed to safeguard against catastrophic failures in mobile phone chargers, specifically targeting USB Type-C ports. ... As you can see from these images, this part has been expertly 3D printed with strategically placed...

Kept everything the same as in original design, just extended it to be 90mm in total.

<p>Kept everything the same as in original design, just extended it to be 90mm in total.</p>

I suggest printing in the orientation shown in the photo above  Print SettingsNoSupports:NoResolution:0.2mmInfill:0%Filament: PLA/PLA+/PET-G

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

(Optional) Use small zip-ties to secure the tubing and cable saver to the underside of the extruder setup (see picture). 5. Attach the Titan Extruder to the Titan Bowden Gimbal Mount for FT-5r2. ... See the following for more information on the complete...

The friction should hopefully keep the cable pushed into the controller, and any nudges will be protected by the bungie. Haven't printed it yet, so this is just the model/concept. ... Updated 2 Part print: Part 1 - Clip :...

It should fit other controller cables as well.You can use a cable tie to make sure the protector stays in placeThere are several versions available for you to print:Gamecube / PS2 / XBox stiffGamecube / PS2 / XBox softGamecube / PS2 / XBox softestN64...

The original design of the printer makes it easy for the cable to get stuck under the bed while it moves around, connecting the cable to a small weight through this pulley allows you to solve the issue easily with a very small printed piece which...

This design mirrors the previous concept by MixedDimensions, albeit with a slightly larger cutout to accommodate the cable snugly and prevent excessive strain on it. ...Update: A newer iteration has been crafted, boasting a longer length while featuring...

From original file from @GeoSfak Didn't feel like drilling my machine and voiding the warranty, also my cable seemed to be very, very tight so created a quick chop in Tinkercad with a little drop on shape and enlarged the actual holder. ... Printed...

Inspired by this design: https://www.thingiverse.com/thing:1091637 Created for the Apple USB-C charging cable that came with my iPad Pro (USB-C to USB-C) Used supports only on the bottom part, which houses the connector, had support blockers block...

########### Watching how the cable from the controller to the heated bed kept sweeping behind one of the right hand (facing machine) Y axis rails, I expected it to one day get stuck should the bed to all the way back then forward. This is a...

I loved the design by Enea https://www.thingiverse.com/thing:371232, which offered an even surface to wind the cable around the charger with a low profile, and you get to keep the euro plug as well, without having to remove it when plugging into a...

Inspired by this design: https://www.thingiverse.com/thing:1091637 Created for the Apple USB-C charging cable that came with my iPad Pro (USB-C to USB-C) Used supports only on the bottom part, which houses the connector, had support blockers block...

... wire through the new plug. Resolder the cable back together, then insulate it for added durability. Reassemble the power brick by gluing the two case halves back together securely. The integrated cable saver is designed to prevent future damage.

<p>The original didn't stay connected too well when printed with flexible filament, so I remixed with external latches that hold better.<br>I uploaded an updated version of the print file, and also added a file with supports configured to make...