gaming controller and headset stand 3d models

If something doesn't fit my requirements i will spend my time to create a better solution and learn along the way. This is was the same case. So i decided to create the *best 'gaming' headset stand the world have seen yet! One week later and after...

... a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. ... It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the back-center. ... A M3-.50 nut is required.

No supports are needed; slice and print the Xbox logo face down. Keep in mind that any imperfections on your printer bed will also cause defects in the final part. Assembly: Acrylic glue or wood glue should be applied to the Xbox plate, then secured...

This is a Headset and phone stand with a rail to put your phone charger under the base to charge your phone.

A headset stand with its base suitable for placing your headphones

I used Cura to define different infill value for the rear part of the vertical arm (100% instead of 20% for the rest). ...The reason was to make this part heavier for stability and tougher to avoid the arm being too flexible.

Based on the Xbox controller, Heliumspoon designed a stand that measures 59mm wide and features a convenient cutout for easy connection of a headset.

Model :- Headset G20 Wired Headset (Physical drawing / clone drawing (not 100% the same), wire removed) - Headset Stand (Inspired by Rexus Gaming Headset Stand)Software: Autodesk Inventor 2018Designed By: @bangkitpramesta==(Some preview are...

Model :- Headset G20 Wired Headset (Physical drawing / clone drawing (not 100% the same), wire removed) - Headset Stand (Inspired by Rexus Gaming Headset Stand)Software: Autodesk Inventor 2018Designed By: @bangkitpramesta==(Some preview are...

Wall mountable xbox controller and headset stand, xbox logo on top part. Category: Video Games

The design has been modified to include a 1-inch extension at its base, enabling the controller and headset to be suspended above the surface rather than resting directly on it, thereby keeping them off the surface the stand sits upon.

Human: French Support for gaming headset Holder makes room for Hyper X headsets with an arch diameter of 4 cm Easy to slide onto the wall Hook design allows for easy testing and printing

Xbox Controller and Headset holder. **the logo is not in relief ... ...in some photos it is but it is a step that I did and that I do not recommend as there is not enough extruded space to fit the logo in It's yet pretty cool with the extrusion...

Wall mountable xbox controller and headset stand, xbox logo on top part.

Headset stand

It holds an Elite controller on one side and a gaming headset on the other. I have not finished the print so I haven't tested it yet. But I will post photos and updates once it's done. ... I'm new to the game so please share your comments, likes,...

It holds an Elite controller on one side and a gaming headset on the other. I have not finished the print so I haven't tested it yet. But I will post photos and updates once it's done. ... I'm new to the game so please share your comments, likes,...

I'm combining elements from two Thingiverse designs to create a custom setup that seamlessly integrates my gaming headset and controller into a sleek wall-mounted system, allowing for effortless storage and organization in my gaming space.

Base to lay your xbox controller and headset in the wall

Support for 2 x-box controller and 1 headset, elegant design and base with x-box controller silhouette.

... hängen kann. ... __________________________________________________________________________ I modified the design so that you can hang a second controller and headset (in my case a Razer Wolverine V2 and a headset) on the other side of the console.

This is a hangar which mates onto the top of the Xbox Series X when standing upright and has a spot for a headset and a controller. The width of 34 mm was chosen to allow for the headset to stay plugged into the controller as well as room for...

I drew inspiration from others' work to design this wall mount. ...It comes in two versions - one tailored specifically for headsets, and another that accommodates both headsets and controllers.

Lightweight Holder for the PS5 Controller and a Headset. Testet with the Sony Playstation Gold Headset and Bose QC 35 but should hold any similar Headset aswell. Can be clipped to any side of the PS5 faceplate. ... Remix of kiwithreeds wall mount...

made this for my Razer Wolverine V2 Chroma controller and Razer Kraken v3 headset for mounting under my desk. ... No supports needed

... but my headset features substantial padding on the band, causing me to knock my controller off when grabbing it. ...To prevent this issue, I lengthened several parts and widened the gap between the headset and controller for added clearance.

Update V3: the new model has more supports, the distance between the 2nd controller and the headset is greater (I accidentally kicked the controller out a few times when taking the headset out. That shouldn't happen now) and there is a hole at the...

I made this from scratch in AutoCAD. It's designed to drape over the top of the Xbox One S while standing on side. It holds an Elite controller on one side and a gaming headset on the other. I have not finished the print so I haven't tested it yet.

Removed the top screw hole and shortened that area. ...also extended piece between headset and controller area a bit to house larger headphones. ...Flip it on it side and use support and 100% infill.

Playstation 5 controller & headset holder, now with a gap for the charging cable because I kept knocking the controller off when grabbing my headset. ... Remixed from https://www.thingiverse.com/thing:5556079.