games workshop 3d printing files

Except for the spacer ring, all parts are printed with ABS for stability and the possibility of stable gluing. The spacer ring is made of TPU. For adjusting the air gap between rotor and stator, the space rings are 1 or 2 mm high and can be...

Print instructionsUnassociated tags: 7 segment, 7 segment uhr, LED clock, LED Uhr, rgb uhr Category: Household Summary Ich benutzte PLA in schwarz und farblos-transparent Benötigt werden folgende Teile Druckteile: (wenn du einen Drucker mit 300x300mm...

I used the #19 drill with the depth stop (as described in the Ford Flat Head Assembly Structures for the threaded inserts) to drill holes for the magnets in the block. The Display Base was too big to print as a single part on my printer, so I split...

The original design for the FT5 is kind of kludgey with the woodcuts and prone to vibration which loosened the X-mount for me and led to a failed print once. This redesign is ahhhmazing. My test suggest ~400mm/s linear motion is possible before X/Y...

I added a ziptie location for the cables (break off the designed-in support), modified a ton of tolerances, got the fan ducts adjusted to the proper height with the nozzle, made a permanent BLTouch mount, embossed "CR-10S Pro V2" and "Micro Swiss...

Once you've printed out this part, and optionally Piercets external tensioning parts, remove the current idler and take the 608ZZ bearings out. Add the additional 608ZZ bearing, put a washer between each bearing and on the top and the bottom of the...

Instructions You'll need 4 of the mosaic feet, and four endcaps - each should be printed with a .3 layer height and no support using an infill level of 15%. As for me, that was enough. A 5/16" length of threaded rod will come in handy as well as...

;-) I remembered this puzzle from back when i was a kid, seeing it at a flea market - and the contest brought it back to mind almost instantly.Although i took a slightly different approach to add a locked gift compartment, which should fit most gift...

Notes: Parts to print: 2x middle, 2x center, 2x center (contains mega x) 4x side, 4x corner Start mounting the middle parts using the original short screws. Once they are fitted you can easily snap in the other parts. To use the corner drawer...

... bright even in a fully lighted room with the K40 LED strip on. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2 Infill: 20% Filament: Amx PLA Blue Notes: Any material will do. ... Category: Art Tools

It is the low-poly and easy to print version of ionic, doric and corinthian columns. Doric and corinthian columns are supportless, only ionic column has some easy to clean supports. Just like chess knight is not photorealistic and just symbolic, goal...

Endstops The Y-Axis endstop is a single mount for both front and back switches, activated by two tabs mounted under the bed with M3 screws, nuts, and printed M3 T-nut converters. The upper Z-Axis switch is clamped to the Z-Stepper motor RHS...

Plus tiny stool.  - Cupboard with microscope top option All the parts are pre-supported for SLA resin printing! This set works together with the Medical Bay set (the table, drawer & cupboard top options are interchangeable - there is also some...

This is inspired by Zack Freedman's weighted Gridfinity baseplates, but puts the weight cavity on TOP so that the model needs NO SUPPORTS to print. As with all my other Gridfinity models, this was designed using CadQuery instead of Fusion 360. See...

The issue was that after a few prints, I had created a really cool "Rock". I wanted to be able to share the wonders of this illusion with the world, so I needed a way to present it. Did you know that "Necessity is the mother of education"? Armed...

The play translates into uneven surfaces which are readily apparent on large flat horizontal surfaces, but also affect every other print in some way. There are a few mods here and you can try all or one at a time. First off, the bearing holders on...

I extruded the design to 1mm, added some fillets, and printed it in PETG. Worked the first try (instead of requiring the expected two redesigns). For those still following along, I installed the video card with the new PCIe bracket into the QNAP....

To build this mod, you will need: - 3 three-millimeter by twenty-millimeter socket head cap screws - 3 three-millimeter by twelve-millimeter machine screws - 3 washers (twenty-millimeter diameter) - 7 #6 or #8 flathead screws (three-quarters of an...

Assembly: Recommend this remix for regular nuts Wind Turbine MK2 DIN934 Remix https://www.thingiverse.com/thing:6098438 Use all other printed parts from the original windmill 1x threaded rod M8x106 mm (M8x116 mm DIN934 Remix) as a wind turbine axle...

Once the case has been printed, the headphone socket can be screwed into place, and perhaps a tiny dab of super glue to hold it tight. The same can be done on the side of the ultrasonic Mic - a tiny drop of super glue before pushing it into...

**Serial Communication**: The code includes Serial.print() statements, indicating that it's designed to communicate over a serial interface, likely with a computer or another microcontroller. 3. **Timing and Loops**: The code uses the `millis()`...

I also have a light-sensitive resistor on it and plan to add a sensor at the rear and one facing down to prevent the robot from driving off cliffs.\r\nI've got plans to be able to extend the length of the track assembly by adding a third cog, but I...

{"I2CDriver":"7,8,9,10,11,12,13,14,15,17,18,20,24,29,31,36,41,42,44,46,48"} => 13 muss aktiviert sein für ADS1115 (https://smile.amazon.de/-/en/gp/product/B07DFX9Q4G) - Printed Battery Pack, electronic coverage etc.) Teile: 5V Motor mit Getriebe,...

Therefore I'm able to connect the geiger counter to my Home Assistant + I added a small OLED Display, to see all data directly when standing in front of it (+ 10 coolness).After the electronics where finished, I've designed an enclosure, based on the...

WhatA modular corner and side holder/guide system that allow the CNC to cut dovetail tracks for the matchfit system into the spoilboard and slide in clamps by removing the walls but leaving the holders screwed to the table.It uses a modular system...

All parts were printed with a 0.2mm Layer height. 3 perimeters, and 20% infill. I used PETG, however other materials would also work. A hardware list is provided. You may also need some basic tools, knifes, small drill bits, etc. Most parts...

In my case I left 40mm of stock cable on stock extruder to easily use in another future project.X Carriage Base Mod - https://www.thingiverse.com/thing:3537449Config is on my GIT https://github.com/Tactical-Koala/AnycubicMegaProKlipperVideo...

The kit will snap into place, and you can refer to the video for instructions on preparing the case for use after printing and how to install the board. * LidNoOLEDConnector.stl: A lid with only cutouts for the click sockets and grove connector *...

EN Translated with www.DeepL.com/Translator (free version)            When printing, observe the direction of the parts on the tray Assembly order 1 Place the 4 nuts (M3 square) in their housings2 Pass the...

By making it modular, I am able to print extra parts to allow the structure to expand and in doing so carry more coins, as many coins as needed. For me with 6 pontoons and one cup, I was able to handle a maximum load of 1.2lbs of coins. In the end,...