gamecube noctua fan 3d models

A fan duct for better ITX case ventilation and CPU cooling, compatible with Noctua NF-A9x14 fan (tested) and possibly for other 9x9 fans. Fan duct net height: 14mm (project file included, can be easily adjusted to align with ITX case side panel).

... The four holes can just be covered with tape to increase efficiency but it works fine as is. The fan I used: https://www.amazon.com/Noctua-Cooling-Blades-Bearing-NF-A4x10/dp/B009NQLT0M/ref=sr_1_2?dchild=1&keywords=noctua+40mm&qid=1614718218&sr=8-2

This mod must be used with CR6-SE (Kit) Power Supply Fan Adapter : https://www.thingiverse.com/thing:4685262 Adapter to replace the **original MeanWell power supply fan** of the CR6-SE with a **Noctua NF-A6x25 fan**. ... **This mod requires a disc...

... But then the (Excellent, btw) case by Malolo would no longer fit over the fat Noctua fan connector. ... I edited the design for an extension that shields the Noctua plug from the top and sides, and is flexible just in case you need some wiggle room.

Human: I'm modifying the fan adapter for the Noctua NF-A4x20 (Noctua NF-A4x10) to fit perfectly on my Creality CR-10S PRO motherboard. Unfortunately, I didn't take a photo of it in action - the case is already built and configured ... ...The...

Hello, I'm replacing a noisy 50x50mm axial fan with a Noctua 60 FLX on my Prusa I3MK2/MK2S printer. This design fits directly onto my printer and might require shorter screws for secure installation. A small hook on the side helps manage cables...

Remix of Scott Yu-Jan's nice minimalistic PSU Shroud for a Noctua fan, but for the Non-Pro Ender 3. The fan cover fits a 60x25mm fan, and a Scott (as well as myself) used an NF-A6x25 PWM fan. ...Check his video for a specific link EDIT: Removed the...

... Engineering Computer-1 case. ...The case is designed to install only one case fan but I wanted to install 2 fans - intake and exhaust, so I came up with a fan mount idea to install Noctua NF-A4x20 as an extra fan. ... Form 2 | Grey Pro v1 | 0.1mm

I designed a custom shim to perfectly fit a Noctua fan on my Prusa I3 MK3 printer. The shim allows the fan cover to sit securely and flatly on the fan itself. ... To create the fan cover, I utilized this innovative design found on Thingiverse:...

To conceal my somewhat unsightly Noctua fan, I install three sidewalls onto the fan grill, courtesy of @ML3DPrinting. One side remains open as this is where the fan cables are located. ...I am optimistic that you can also cover other 4010 or 4020 fans...

Here's a simple CPU fan shroud designed specifically for the Fractal Design Node 202 case, engineered to work seamlessly with the Noctua NH-L9 series of CPU coolers in various builds.

This is a custom design, based on the original Noctua 60mm Fan Holder for Cetus 3D, since the existing version exceeds the space available in my enclosure. ...Print it as a solid object without supports to ensure maximum stability.

I designed this because I used the Noctua A6x25 mounted facing down like the original design and found that the fan will come on quite strong and produces a lot of wind noise. ... In this arrangement, the wind will blow more directly to the...

... You just need to print, unscrew the nuts on the top, install the printed mount, screw the nuts, install the Noctua fan 12 VOLTS! (you can install it with the rubber Noctua mounts or the screws) and plug the noctua fan in to 12 VOLTS! red connector.

To install a Noctua A6x25 FLX fan running at 12v on your Two Trees Sapphire printer, you'll need to utilize the existing fan mounting holes. The 60mm fan fits snugly under the Sapphire even with its steel plate attached. This setup doesn't increase...

Meanwell LRS-350 Noctua A9 92mm fan cover ------- This is a cover replacement for the Meanwell LRS-350 power supply to mount a 92mm Noctua A9 fan. Other 92mm fans could fit as well (82.5 x 82.5 mounting pattern). A cover for both the 25mm and 14mm...

Noctua NF-A4x20 Fan Mount and Shroud for Creality CR-10S Pro V2 Custom Cover to Conceal Noctua's Beige Fan Custom Fan Shroud Boosts Airflow on OEM Hotend...

A simple fan shroud to cover a Noctua 60mm x 25mm fan, the wall on the side just makes it look a bit better when the fan is mounted externally and hides any cabling, for example when used on a Ender 3 Pro PSU. There is no hole for the fan wire, as I...

These are replacement fan blades for an 8 inch desk fan. These have been designed to be compression fit to a 6mm fan motor shaft. The design was inspired by the Noctua NF-A12x25. ...Fewer blades have been used to reduce the weight.

Required material: Noctua NF-A20 2x countersunk head screw M5x12 2x self-locking nut M5 (It cannot be a simple M5 nut) Optional: 4x screw M4x35 4x nut M4 You can also use the supplied rubber holder included with the fan, but they are hard to remove....

This is a fan adapter to replace the stock CoolerMaster CPU fan with a Noctua NF-A9 PWM in an Acer XC-1660 PC motherboard.This fan adapter converts the 71.5mm stock fan bolt spacing to the larger square shroud on the Noctua NF-A9 PWM at 82.5mm. The...

... in the center, showing the actual modification. When the project is ready it can be used to cover the original noctua fan with a personalized protection. ... This project is still in progress, and there will be updates with the changes soon.

#### Changelog ##### V1.1 - Lower the locking fins by 2mm (was incorrectly measured) and make them slightly wider for increased strength - Reinforce fan screw holes - Grow Noctua fan slot by 0.2mm to improve tolerances - Remove 0.2mm from front and...

I was modifying my Prusa MK3 with new MK3 mods and this required a swap to a Noctua 40mm fan. Wolfgang's fan cover is designed for the MK3 and won't work on the MK2/S. I removed the back side of the fan cover so it wouldn't interfere with the...

The Noctua NF-A9 PWM chromax 92mm fan I used can be found here on amazon:...

This is a remix of "dkcwenge" design of fan duct for Mega-S i've changed the connection holes, so a noctua Fan (40x10 or 40x20) would fit without screws now ;) Thank you for providing the step files ;) i've printed it with tree support, the only...

A fresh redesign of the hood, crafted by hellc2, specifically for a Noctua 80mm fan. This cover boasts fewer holes than its predecessor, engineered to optimize airflow within the housing. ... The design has also been elevated in height, allowing the...

This remix is a compact adapter for a dial gauge I purchased from Amazon that snugly fits over a 40 x 10mm Noctua fan, or any similar 40x10 fan, attached to the front of the CR-10 Heavy Duty customizable modular e3D V6 mount Volcano 5015 ABL found on...

This is a small case with a window for a Noctua fan controller. There are 2 slots to run wire out of and room in side to bundle up or hide excess wires. ...The knob is press fits into the fan controller if you want it to be bigger.