gamecube fan mod 3d models

A different fan than what's typically used also necessitated the offset on the left side. Not everyone may find this useful, but I'm posting it for those interested - the brace has significantly improved the quality of my prints. ...The left and right...

Link to the video where I use this case: "Adding a Noctua 60mm Fan to the Ender 3 Pro's Power Supply (PSU)" https://www.youtube.com/watch?v=C4raTp9DZa0 Link to my RC channel: https://www.youtube.com/channel/UChb38m6f-uV_DL-LkGiD3NA The LM2596s Buck...

For details how to print PSU_Cover_Fan look in the original design (https://www.thingiverse.com/thing:4897394) I have only changed the alignment of the two holes on the side with open end, because they was out of place to screw in the cover...

For details how to print PSU_Cover_Fan look in the original design (https://www.thingiverse.com/thing:4897394) I have only changed the alignment of the two holes on the side with open end, because they was out of place to screw in the cover...

A 40mm fan mount has been included. An EZABL 11.85mm diameter inductive probe mount has been added. This setup is very lightweight yet strong, using ABS filament. The E3D Hotend setup is currently in place (with an upcoming upgrade). Print Settings...

will see if I can compensate the design but it will not cause an issue.        One millimeter to spare at the front support 2020bar  If you are still rocking the 10mm fan i've added a 10mm version also (standard)any suggestions or design-wishes let...

I cut the silicone sock shorter and made these shorter fan ducts to direct the air where it is needed. I'm not a designer so the model isn't the greatest with the hallowed out inside looking a bit weird (stepping at some points rather than smooth)...

I reused the original design, made it smaller, faster to print. ... It works fine with big staples, I was able to unmount the gamecube power adapter.

... Enjoy your GameCube! _Note that this part should fit over the Wii power connector in one way, don't try to fit it on reversed, you will do damage to your GameCube's PCB. ... I used the remixed Thing for the source of the GameCube connector itself._

...I've included 2 types of the shell one with and one without the vent sides so you can print them later and glue into place or design your own. the other is just the standard GameCube.Notes: Print it so the top of the GameCube is facing the print bed.

i adjusted the location of the ducts down lower by 3mm if you need it adjusted more let me know. i have not tested this yet. i am using a different hot end than every one else. ...i have the new spider 3.0 high temp and flow hot end from creality

Suggest: Develop thermal resistant materials for printing that can withstand temperatures above 200 degrees Celsius. ... WARNING: Droopage caused by plastic softening at high temperatures may lead to snagging on cooling ducts with printed objects.

i adjusted the location of the ducts down lower by 3mm if you need it adjusted more let me know. i have not tested this yet. i am using a different hot end than every one else. ...i have the new spider 3.0 high temp and flow hot end from creality

The design was revised to increase the size of the hole through which the heater block passes, ensuring that nearby materials do not overheat and melt. ...Additionally, the outer edges were rounded to create smooth curves with a consistent radius.

Lock Designed to Prevent Patio Umbrella Spinning Around When Tilted to Block Sun. Engineered specifically for a 37mm umbrella pole, this lock may also work with poles sized between 36-38 millimeters. It's designed to keep your patio umbrella...

Search user "Just Printed_3D" on Youtube and find videos there on how this extruder cover is mounted. Also choose to integrate an Bed Level Sensor if you want to upgrade your Sidewinder X1. ... Videos are available in english and german language.

Замена штатный вентиляторов на на вентилятор 5015 печатал ABS слой 0,2 заполнение 100% Не стал делать отверстия для крепления вентилятора так как есть множество вариантов.

A person had to trim down a small amount to accommodate their unusual print head design.

Human Error Reduced to Near Zero Strong Mode June 29, 2020 - Update for Enhanced Performance

Convert 2d cad to 3d model of Separator Machine👇👇Visit Further My Portfolio👇👇3D CAD by Anykolab: https://www.cgtrader.com/anykolabStock Photos by...

I Use an E3D V6 With this mount from thingiverse at www dot thingiverse dot com forward slash thing colon 491084 but encounter a problem with the nozzle I'm trying out The modification moves the nozzle back 20mm so I can now use the awesome nozzle...

The default blower placement on the Zonestar Z5X is completely absurd, and it barely cools down the filament coming out of the nozzle. This used to cause a lot of curling on the right side of parts when printing PLA. At first, I decided to design an...

<p>Comes in 4 pieces, split STL to objects in prusa slicer. There's a 0.5mm gap between parts; mask back panel, snap pieces into back panel, and fill gaps w/ JB-Weld or similar. This is to allow everything to fit on the bed and account for tolerance...

Customized version of http://www.thingiverse.com/thing:735038 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=735038 Instructions Using the following options: az_manufacturer = 0 ds_fan2 = 4.3 ds_fan1...

Remixed Design with Lower Build Plate. ...I modified the original design to clear the heated bed of my standard CR-10, ensuring a safe and smooth printing experience.

WARNING: This design may exceed the clearance of Ender3 Stock Airflow due to its increased height. The original airflow has a fixed height of 9-10mm, while this remixed version stands at approximately 16mm. Verify your nozzle's height from the...

For my Ender 3, I expanded the outlet from 2.5mm to 4.5mm and extended it by 2.5 mm, adjusting the source designs accordingly. There is still a 2.5 mm gap between the nozzle's bottom (or build plate) and the cooler's bottom. I also reinforced the...

Convert 2d cad to 3d model of Separator Machine👇👇Visit Further My Portfolio👇👇3D CAD by Anykolab: https://www.cgtrader.com/anykolabStock Photos by...

I struggled to detach the support documentation without snapping the securing clips.

<p>Could never find a shroud i liked or that wouldn't keep melting from being to close the the block. I also wanted a better viewpoint of the nozzle. This remix covers both of those issues.</p> <h3>Print instructions</h3><p>I printed in Priline...