gaggia classic with pid 3d models

It perfectly fits on my Gaggia Classic's 58mm portafilter, which has an outside diameter of 69mm. After printing, make sure to add support everywhere for a solid print. To achieve the best results, I recommend using a finer layer height than the...

I designed this funnel to fit the Mahlkönig X54 grinder and Gaggia Classic Pro. It is designed to prevent the coffee grounds that would normally fall out of the portafilter during grinding or when using a WDT tool. It does not require any built-in...

I loved this espresso accessories shelf, but it didn't fit the offset lugs on my Gaggia Classic Portafilter. I designed this one with two Ø64.5mm spots for a tamper and a WDT tool, and a hanger that fits this funnel I designed for IMS baskets. The...

This slim tray allows the use of taller cups and scales with all Gaggia Classic models, including Pro.The most difficult part of printing a drip tray adequately is getting it water tight, and the bottom part of this model helps with that.I recommend...

Customized version of https://www.thingiverse.com/thing:104728 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=104728

Customized version of https://www.thingiverse.com/thing:104728 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=104728

Customized version of https://www.thingiverse.com/thing:104728 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=104728

Customized version of https://www.thingiverse.com/thing:104728 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=104728

Customized version of https://www.thingiverse.com/thing:104728 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=104728

Heavily inspired by rotf101's tamping-station (but created from scratch) - see "model origin" for link.I made this for my bottomless portafilter that come with my 2nd hand machine. ...I have a shades of coffee wooden handle that I fitted to it, but I...

Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=104728 Using the following options: • tray_height: Adjusted to 5 units high. • Tray width: Specified at 98 units, a customized dimension. ...

This is a dosing funnel for 58mm Gaggia portafilters with IMS baskets. This has been designed for 3mmx3mm cylindrical neodymium magnets. The magnets press fit into the funnel. If I was making it again I would make the whole a little bigger...

This is the updated Gaggiuino housing for a Gaggia Classic or Classic Pro espresso machine. It is designed for an Arduino Nano and a Nextion touchscreen display to control temperature, pressure, and display output weight. It allows for programmable...

Gaggia New Classic portafilter holder for Brewista Smart Scale II. Assembled using [4x20mm pan head universal...

Replacement porta filterhandle for original Gaggia Classic Coffee Portafilter. Slightly overdimensioned but robust! ...Print out of PETG, because of the temperature at the portafilter.Screwed on with the original screw.

The PID is a ubiquitous REX C-100 clone with a set range of 0-400C and a single alarm output. Note that the traditional DIN panel mounting ring cannot be used with this enclosure because... I forgot about it. If time permits I'll mod the case to...

**UPDATE MAY 22, 2020**: Realizing it's not a printable model at present, I'll spend some time rectifying this soon. Unfortunately, I've misplaced the original model file, so I'll recreate it from scratch again. Hopefully, an update will be available...

This creation was crafted using Tinkercad. ...Modify it directly online at https://www.tinkercad.com/things/bQVXGZxw6jR

<p>This replaces the whole pump mount plate and the rubber dampener. I bought a used machine where the plate and dampener were missing and turns out the plate is not being manufactured anymore.</p><p>Best printed standing upright, without support...

I really like this extension because you can take out the scale to use on the counter and the drip tray just rests on the sides of the base. It is a low profile drip tray, I need to drain it after each flush-brew-flush cycle. Cleaning is quite easy...

Edited design to lose the flat lip from the bottom as the surface area wasn't needed for wall mounting.

the hole for auto empty water is 12.6mm for 13mm thread

A straightforward upgrade solution for the Gaggia 14101 Classic Espresso Machine's standard drip tray cover, designed to fit perfectly without any modifications required.

Parts required to integrate load cells into the drip tray of a Gaggia Classic Pro espresso machine. ...Part of the Gaggiuino project.

Credit to LikeableBump for the base model, designed for Gaggia Classic Pro (Gaggiuino - Arduino &amp; Touchscreen Housing for Gaggia Classic &amp; Classic Pro v2 by LikeableBump - Thingiverse).Fasteners (to attach touchscreen housing):&nbsp;2 M4x10...

... drip trays and grids (note: the grids are not cross compatible). ... It was based around the timemore scale which overhangs the existing Gaggia Classic tray and so a custom design was needed. ... The scale feet are 93w x 115mm so other scales may fit.

This is a custom-designed espresso machine funnel that perfectly fits the portafilter of the Gaggia Classic paired with the Eureka Mignon Specialità grinder. It's specifically engineered for use with the Eureka grinders, which means you don't have...

... funnels. I've made 3 versions: 1) For stock Gaggia portafilter with 25mm ears 2) For E61 portafilters with up to 30mm ears 3) For aftermarket Gaggia portafilters with up to 30mm ears ---- Update 1/21/22 -- Increased E61 ID for better fitment

... of the drip tray is extended out to the sides so that it is able to hold more water despite the low profile. The extended area is also designed so that it can be printed without supports, and will almost not need a support when in the Gaggia