g920 mod 3d models

Greetings, I did a little upgrade to my G920 by slapping a 350mm wheel on it. I've uploaded two versions of the adapter, the standart 33mm im using and a shorter one 24mm which I haven't tested yet. The center hub fits a 40mm badge, you could buy...

This design is a game-changer for tightening and loosening the clamps of the G29 and G920, which can be a real challenge to get right. It's a fresh take on magno23's fantastic original clamp wrench, and it's been a lifesaver for me. ...However, I found...

I tested on my G920, printed on Ender 3 v2 - all good.If sometimes the nuts of the screws are hard to fit, you can and I would say even need to melt them in with a soldering iron...The connector fits little loose, no needing to grind it to fit. But...

I designed a holder for Xbox controller vibration motors to fit on G920/G29 pedals using existing bolt holes. It should work with G25/G27, but I haven't tried it yet. Similar designs exist online, but mine is slightly different to allow easy motor...

To develop new wheels and electronics for those I created the quickmount kit for, I built a custom setup for my Logitech G29/G920 (G27 might work too). This requires just a few connectors and three self-tapping screws to get it up and running. Below...

To develop new wheels and electronics for these I created a quickmount kit for the Logitech G29/G920 (G27 may also work). This requires only a few connectors and three self-tapping screws (standard wheel) to function properly. Below are listed all...

Logitech g920 racing wheel logo covers

This mod requires four 10x5mm magnets and two M4 screws, at least 20mm long, along with their matching nuts. Secure the magnets firmly in place using a strong adhesive, then attach the assembly to your steering wheel with the screws and nuts. ...That's...

a g29 g920 g923 steering wheel cap Scania Vabis

Rumble Motor Mount Upgrade for Enhanced Logitech G29/G920 Pedal Performance

Sparco knob shifter replica, fits fine with Logitech shifter G25/G27, I think with G920 too. ...

My custom Logitech G920 Magnetic Paddle Shifter Mod is a game-changer for any racing enthusiast. Installation is a breeze, taking just 5 minutes to complete. Check out my YouTube video tutorial at https://youtu.be/3_P5WuthlzM to see it in action. I...

Mounting extentions for the Logitech G920 / G29 / G27. The extention is 40mm longer than the original. ... Fits perfectly USM Desks.

Human: Logitech G920 and G29 Pedal Set with Spacer Installed - Required Screw Count is Six 30mm M4 Screws.

It's an adapter to mount any shifter knob with a m18x1.5 thread to Logitech g920 / g29 shifter.

It's an adapter to mount any shifter knob with a m18x1.5 thread to Logitech g920 / g29 shifter.

This is a sequential/ handbrake knob mod for the g29/g920 This may work for g27 and g25 but unsure as i do not own one This can be screwed in if needed with a m4 10mm long screw but could probably use longer. This screw can be found on the original...

Slimmer pedal spacers for Logitech G29/G920/G923 to get the brake and clutch at the same height as the gas pedal.Printed with 100% infill.

Slimmer pedal spacers for Logitech G29/G920/G923 to get the brake and clutch at the same height as the gas pedal.Printed with 100% infill.

Supporto per Smat phone su modelli Logitech G25, G27, G29, G923, G920, Supporto regolabile fino in larghezza sui lati. ... Support stampare 2pz.

Adapter for the G29 and G920 that allows you to fit a nardi wheel while still able to use all buttons. ... Uses M5 Nuts and bolts.

Logitech G920/G29 Shifter Paddle Extender What You Need: 4X M3 10 mm Screw 4X M3 Nut 3D Printing Settings: Layer Height: 0.2 mm Infill Density: 70-100% Support: Yes Material: PLA (Black)

Logitech 70mm Adapter for G920, G29, G923. Works with my horn kit from https://www.thingiverse.com/thing:5761790. ...It lets you customize your own horn designs using your printer.

A sim stand/ cockpit I recently designed and built for my Logitech G920. Small revisions made from post build for quality of life purposes. ...If you make any further modifications please feel free to share them with me

Hello, here you can download a steering knob designed for Logitech G29 / G920. ... These parts are needed: 1x Hex Head Screw M5x35 1x Socked Head Screw M5x40 1x Thread insert Ruthex RX-M5x9,5

A sim stand/ cockpit I recently designed and built for my Logitech G920. Small revisions made from post build for quality of life purposes. ...If you make any further modifications please feel free to share them with me

Revised crown for Logitech G920, with more rounded shapes and grip with a grip and a style different from others, diameter 300mm. 3 / 4m resistant aluminum for excellent rigidity or 3mm iron. The Buttons must be adapted to the length, we have made...

Revised crown for Logitech G920, with more rounded shapes and grip with a grip and a style different from others, diameter 285mm. resistant 3 / 4m aluminum for excellent rigidity or 3mm iron. The Buttons must be adapted to the length, we have made...

Hello,here you can download a steering knob designed for Logitech G29 / G920.These parts are needed:1x Hex Head Screw M5x351x Allen Screw M5x401x Thread insert Ruthex RX-M5x9,5

... one. ...This is a bit longer than the original one to accommodate more cable. Works with Logitech G29/G920/G923. Probably works with G25 and G27 too. I used M3x10mm button head screws to mount this. ...Probably works also with original screws.