g920 mod 3d models

Some overhang areas in the inside don't bridge well, so you'll need to do some trimming / post-processing.Updated 5/2/2021:I added aluminum foil tape (HVAC duct tape, buy at any home/hardware store) for 3 reasons:serve as heat spreader so that the...

Offset X: (+/-) 58.565 mm / Y: -11.00 mm - 30mm heatsink fan mount - 40mm heatsink fan mount ####Remix Based on the V6 mount by graham01 https://www.thingiverse.com/thing:2471011 and the dual 5015 fan mod by RebelRousingProps...

However, I changed a various things and thats why I publish this mod. My modifications: - I created a new cover because the original one cover was not fitting, - The original rover's cam mount was made for that whoop AIO nano cams and image was...

I used 10mm screws left over from the Z-brace mod. You will also need a push-button with a shaft no wider than 16mm and a collar/nut between 16mm and 25mm. I pulled my button from my collection, but it was like this one from Adafruit. Those two...

- The position of the H2 was changed from the original (thanks @morganlowe for going into the source files and modding that for me...) to allow space for a second fan between it and the backplate, which brings me onto the next part: dual fans. -...

... diameters from left to right: 1.79, 1.81, and 1.83. The 1.83 set has the best pointer alignment (closest average) for both nut measurements, 1 pointer or +\-50um. Designed in Fusion 360 and printed on a Cetus mk2 extended with a few mods. ... Peter

9-2-14: Reinforcement of 9g servo mount and added the Sketchup file so anyone can mod it for a particular servo. Print instructionsPrinted with PLA plastic at 200 micron and around 7% fill. Mount the two front arms to the main body with a single...

Cooling_Fan_Toolhead_CAN_Board This MOD arises from the need for active cooling on the Toolhead Board CAN for VORON2.4 350 Afterburner with cable chain. When printing ABS or other materials, with the doors closed the Toolhead Board CAN reaches...

I printed them on my modded direct-drive CR-10 with a 0.8 mm volcano nozzle and 0.4 mm layer heights. You can probably use your normal slicer settings, I just wanted to cut down on print time as much as possible. No brim needed, 100% infill.</p>...

Primarily designed for my Zaribo-modded Prusa i3 MK3S, but I adapted the design for 2020 extrusions as well (for my Alfawise U20), and for a friend's request I made a tabletop version. You'll need four 608 bearings as well.</p> <p>The holes are sized...

... G27 Hall Effect Mod V1 by James Burroughs (Video Links at bottom) Printing Instructions: (Print Layout is in Pictures) There is not much stress so I used 4 walls and 4 top and bottom and 10% infill seemed to do the job. Use 100% infill for the cap.

Even better cooling is being developed and a few other mods to improve endurance over longer distances. Water cooled esc's are easy off the shelf for model boats etc and I may build enough space for a cheap (solar fountain type) water pump in the...

If you have one of the Prusa MK3 printer series printers, I highly recommend you check out Grégoire's excellent enhancements to this printer:Bear Frame Upgrade 2.1Bear Extruder and X Axis (BearExxa) - This is v1; hopefully by the time you are seeing...

Even better cooling is being developed and a few other mods to improve endurance over longer distances. Water cooled esc's are easy off the shelf for model boats etc and I may build enough space for a cheap (solar fountain type) water pump in the...

If you have one of the Prusa MK3 printer series printers, I highly recommend you check out Grégoire's excellent enhancements to this printer:Bear Frame Upgrade 2.1Bear Extruder and X Axis (BearExxa) - This is v1; hopefully by the time you are seeing...

I modified this thing: http://www.thingiverse.com/thing:93042 By Aeropic The mods were to get the magnets to the 60mm spacing, and to open up the center to allow the Titan extruder to fit. Unfortunately, due to the size constraints, the hot end tip...

- [Aménagement 2eme classe](https://cults3d.com/fr/mod%C3%A8le-3d/jeu/kit-2eme-classe-du-tramway-de-campagne) pour la Voiture bois à plateforme ouverte. (0,65 €). à venir - Fourgon à bagages - Voiture postale - Voiture restaurant <h1>...

This mod is highly recommended for probes using a normally open configuration, as crashes would be more likely (e.g. Piezo, BLTouch). Wire the switches as NC (normally closed). You can wire all three in series and hook up to one spare endstop (say...

Introduction:\r\n\r\n*** This mod blocks the vision positioning system (VPS). Keep this in mind, and you may want to disable VPS *** I personally have not had any problems. Please be safe with this project. Never fly a drone directly over people or...

I am including the SketchUp file in case it helps someone with mods.&nbsp;My PayPal tip jar: https://paypal.me/design8studio &nbsp;&nbsp;Various LowRider 3 CNC remixes:LowRider 3 CNC Collection&nbsp;View all my models and remixes on...

If you're into modding, a stock blaster catch/trigger/lock spring could also do the trick provided it's the right length. More detailed instructions are included in the README.txt file. Enjoy the build, and happy foam-flinging. If anyone gets...

this is an afterburner direct drive mod for the "tronxy x5sa pro" In Y axis you lost 10mm print space ------------------------------------------------------------ V3 is now online in V3 you can use the origin tool Holders: Thanks to...

If you want to run LEDs and an Octopi off the same psu you need to upgrade. One of my many mods to the printer was to get a Mean Well LRS-350 24v psu which is the successor to the NES-350 24v, the only real difference being reduced cost (about $20...

Since my print bed can't do it's full 200x200 anymore due to mods (this still wouldn't have fit anyway - it's a tad larger than 200x200), I cut it into four manageable, bite-sized pieces. Print it in pieces and glue it together (I like this cement...

I'm making available a copy of an older version of the DF83AntiPopcorn as a Tinkercad project at https://www.tinkercad.com/things/eQNVTkmjZPR-df83-anti-popcorn-insert-public feel free to copy and mod it, non-commercially. ... Video of the Shroom in...

Mullet mod for the cam/vtx is recommended, but I have included a normal camera mount if you haven't done a mulletmod before. (if you haven't, look it up on youtube it's perfect) tip: solder the motors to the underside of the FC. This allows for easy...

https://youtu.be/qVt5hHUtp3o 6) Modded the mag release mechanism. Basically shortened the spring hole to have the spring slightly under compression. Also to not need such a long spring which I didn't have. 7) Updated the follower to be taller. The...

Risers You'll need your printer at least 30mm off the ground for proper clearance with these mods. For that purpose, I've created a couple of different riser/feet options: This one uses the stock rubber...

The brace will help stabilize the frame and the added room gives you enough space to easily run a 330x330mm hot bed surface. For this mod, you will need to purchase: • 2 - 7/16-14" x 36" Steel Threaded Rods -...

Once my printer arrived, I completed the mod for the Raspberry Pi/Control Panel mount and started working on the Gantry Support. I realized right away that the original part would not work in it's current state, the bed would hit it when it moved all...