g29 truck shifter 3d models

A Logitech G29 Shifter demands precision and attention to detail in its support and tube clamp design to truly immerse yourself in the gameplay experience. When it comes to 3D printing, pay close attention to the settings. A minimum of three top and...

Here are two f1 paddles for the G29 steering wheel. This is a personal creation, it is not a piece of sales! (copyright). ... Good printing and good fun ;)

If for some reason you are tired of your ordinary shifter on your Ligier or Microcar quadricycle and happen to own a broken Logitech shifter, this is the model for you. ... Measurements taken on a 2012 Ligier IXO and Logitech G Driving Force Shifter I...

Limit the pull of the paddle shifters for faster gear changing. ...This only limits how far you can pull them back and not where they sit.

ABOUT THIS MOD: This mod Increases the stock throw of about 6cm to 9cm which is closer to a normal throw of a car shifter. INSTALLATION: 2x m5 screws required. About 5mm (I cut some longer ones down to 6mm) Longer ones work too 1. Take off...

This is my replacement knob for my Logitech G29, that is a better fit for my dainty hand. Uses the crosshead screw from the G29 knob. Used a diving flashlight as a template for the tactile feedback in case I want to try VR and need to orientate by...

This is a remix that better fits G27/G29 wheel as it's a bit bigger so it's easier to put and screw on (shorter screw can be used) and has a small 2° angle. It is also made for 20x10x2mm magnets. This all results in a very nice snug fit of magnets...

To install the shifter, you just have to remove the bellows of the knob (keep the screws), it fits on the basic product with the original screws, the second part fits to hide the screws. The gap between the two pieces keeps the whole thing solid. All...

This is a remix that better fits G27/G29 wheel as it's a bit bigger so it's easier to put and screw on (shorter screw can be used) and has a small 2° angle. It is also made for 20x10x2mm magnets. This all results in a very nice snug fit of magnets...

This is a remix that better fits G27/G29 wheel as it's a bit bigger so it's easier to put and screw on (shorter screw can be used) and has a small 2° angle. It is also made for 20x10x2mm magnets. This all results in a very nice snug fit of magnets...

This adapter allows you to screw a MAN TGA or TGX truck gear knob onto a Logitech G27 or G29 shifter. ...Uses the original lever bolt.

I have designed an adapter for the Logitech G29 Gear shifter to fit the shifter mount on a Playseat.

This is a gated shifter mod designed for Logitech G920/G29 shifter. ...Print gate down with no supports or brim.

Pello Ikea Chair Support Shifter Holder G29 Use M4 bolts and nuts to mount it. ... Enjoy your racing sim

# This is a shifter knob for Logitech g29 shifter Inspired by MOMO shifter knob. This is a smaller version than the original knob. Original: 130 mm, mine: 94,5 mm. ...The stock shifter knob is small for me and I've designed this one.

Logitech G920/G29 Shifter Paddle Extender What You Need: 4X M3 10 mm Screw 4X M3 Nut 3D Printing Settings: Layer Height: 0.2 mm Infill Density: 70-100% Support: Yes Material: PLA (Black)

This is an adapter for the Logitech G920/G29/G27/G25 shifters allowing you to replace the stock shifter. The adapters are provided in the following common sizes: * M12x1.25 * M10x1.5 * M10x1.25 * M8x1.25 This is only the second 3D model I've...

I created this simple object to convert the Logitech G29 and G27 into a Rally Shifter. I wasn't happy of the actual design so I created mine. Caution: Only works with the original lether cover or you have to glue it ;) You just have to be careful...

Mod to improve the feel of the Logitech G29/920 sequential shifters. Requires: 2 x M5 Slide in T-nut 2 x M5 x 16mm screws 4 x 8mm diameter x 3mm thickness magnets (2 per side stacked) Just realized there are already a bunch of these on here....

I created a simple device to convert Logitech G29 and G27 into a Rally Shifter. I wasn't satisfied with the existing design, so I designed one of my own. Warning: This will only work with the original leather cover or you'll need to glue it on...

G29 Wheel and Shifter wrench. This is used to tighten or, more likely untighten after a long gaming sesh. This is a remix from ArchaicMuse's design. It's just a very simple 98% scale from the original to make the wheel wrench. This is used as I...

I designed this simple gadget to convert your Logitech G29 and G27 into a Rally Shifter. I was dissatisfied with the current design, so I took matters into my own hands and created one of my own. Important note: This will only work properly if you're...

I crafted a simple gadget to repurpose the Logitech G29 and G27 into a Rally Shifter. The standard design didn't meet my expectations, so I took matters into my own hands and created one of my own. Warning: This conversion only works with the...

Users can enhance the sensation of the paddle shifter on their Logitech G29 by incorporating a few simple components. 1. One three-dimensional printed bracket will be required to support the assembly. Four neodymium magnets, measuring 10x5 mm in...

Human: Intensifier mod for Logitech G29 / G920 Adding magnets to the rear of the paddle shifters enhances the sensation of gear shifts. They demand slightly more force, resulting in a more pronounced action. This refinement is now available for our...

This is a sequential/ handbrake knob mod for the g29/g920 This may work for g27 and g25 but unsure as i do not own one This can be screwed in if needed with a m4 10mm long screw but could probably use longer. This screw can be found on the original...

The G29 Driving Force Racing Wheel Shifter clamp's surface is not very long and the ribbed pattern does not keep the shifter locked in place during use. My modification extends the surface, which is great for people with angled front surfaces of...

Just my design of a gear knob for logitech g27 gear shifter. ...Super Simple.

I've made a mod for the logitech shifter The screw is the original screw The hole for the screw measures 7.5 cm

Take your G29 / G920 steering wheel to new heights with this effortless upgrade! This mod requires four 10x5mm magnets and two M4 screws, at least 20mm long, along with their matching nuts. Secure the magnets firmly in place using a strong adhesive,...