g scale buildings 3d models

A simple G scale lantern for your garden trains. No supports required, just load and print.The only part not included is the lens. I used 1.5mm clear acrylic and tinted with Tamiya clear read paint. Any clear plastic can be cut to fit the hole. ...I...

https://www.thingiverse.com/thing:3593060 ---------------------------------------------------------------------------------------------------------- G scale extension ladder designed to be printed with ease, requiring no raft or supports whatsoever....

A gigantic G-scale tunnel boasts integrated track placement holes. This necessitates a minimum of a 300x300x300 printer. Print it with the tunnel hole facing upwards. ...I encountered some problems with the topmost level as I employed very minimal...

Suitable for G scale 1:29, these interlocking fence sections were designed in Tinkercad and can be press-fit together in either a straight or 90° orientation. A gate, ramp, dock, legs, and slanted railing were also designed. The slanted railing...

This design is used to generate clips to hold sections of G-scale model train track together. The SCAD file can be easily edited using OpenSCAD to generate clips with different gaps, as may be needed for different brands of track or in the case with...

This is a double bogie designed specifically for G scale (45mm) garden railways. I created it as a remix of the popular open freight car model in 1:32 scale gauge 1 by UTJTrain, making modifications to the bogie axle to accommodate the double bogie...

I'm thrilled to share my debut design, a G scale pipe railing with mounting plates that's sure to leave a lasting impression. In 1:24 scale, the pipe boasts a diameter of 2.5 inches, standing an impressive 39 inches high and stretching an astonishing...

This is a set of parts designed for making a G scale /1/24 scale station canopy, bench, and station lamp. The station canopy is inspired by old British canopies and has a modular design. All the parts have dovetails that allow them to be printed...

This is a remix of a very, very nice lamp posted by SlashDev http://www.thingiverse.com/SlashDev/ My changes include: making the lamps slightly taller adding an anchor to help install the lamps in a drilled hole adding a glass shade made from...

A simple well car I designed for G scale. You'll need two prints of the half-frame, one print of the well, and 10 copies of the half-beams to create 5 full H beams that support the well under the car. ... The dual wheel bogie I used can be downloaded...

Print Settings: Printer: G Max 1.5 XT Rafts: No Supports: No Infill: 100% Notes: Printed with PLA on a heated bed at 60 degrees Celsius. When placing the seat-backrest on your print surface, ensure the seat face is facing downwards and the slots or...

This signal is designed specifically for the G scale garden trains and requires multiple steps to print.\r\nA suitable replacement for the signal mast could be an aluminum tube repurposed from old garden lamps that have stopped working.\r\n\r\nThe...

I have now fitted 9 of these buffers to my G scale layout. It has become obvious that there is a problem with the two conical screw supports in the rail stop bottom. They break easily. So Drill them out to about 2.7mm, and use screws that are long...

This is a G scale model coal pile that fits into the POLA coal bunker. It is printed in a generic black PLA that I still had lying around.</p><p><strong>Update:</strong> After 2 months outside in the garden and in the sun, the PLA did deform a bit.

This is for my G scale Train set. Wanted to have a train station. Parts were all laser cut. I used Luan wood for most of the parts and some .1inch thick plywood for the window and door trim. I also trimmed out the sides with balsa wood and...

The standard back-to-back distance for G scale wheels is about 40mm, with 6mm wheels including flanges. The inner dimension of the re-railer must accommodate this distance while still allowing smaller cleaning wheels to pass through without binding....

A simple yet elegant G scale stone-type arch was my goal. The problem lay in its size; it couldn't be printed as one piece without overwhelming my capabilities. Therefore, I had to divide it into four manageable sections. To keep the structure...

This replacement railroad tie for G Scale trains serves as a solution for brass track that has faded away over 15 years. To preserve the existing 5ft long flex track, I've designed this new tie to be installed where no ties or underlying plastic are...

Here I designed a points motor for LGB turnouts, which may also work with other g-scale brands. It's mountable on both sides of any turnout. The assembly process is quite straightforward: First, clean up all the parts to remove any errors caused by...

Scaled up to 45mm Gauge/G Scale (~1/22.5) and modified to take LGB pickups and a cheap motor to run on LGB track under power from the rails. Check out the video here https://youtu.be/3qHomxPH6lE A full print requires: 4 x handrails 1 x front...

K Brake assembly for large scale freight cars

This is a door to a grand scale station. ...1:22

Parts to build a heavy sawmill including carriage, saw assembly (complete with all pullies and reversing lever), and track. Log holders and dogs are adjustable. Use .03", 3/64", 1/16", 3/32" brass rod and 1/8" plastic rod for the pully axles and...

This is a simple stone tunnel entrance for your large scale layout. The opening is 260 mm high and 185 mm wide. The included files are supposed to be mirrored to receive a full portal. ...The Overall size of the full portal is 310 mm x 280 mm.

This is a model of a 2D-F1 Archbar train truck in 1/20.1 scale. I am planning to make different sizes of this truck to make logging equipment for my railroad. I will post as I modify the models. I used 3mm stainless axles cut to 1.86" long and 3mm x...

Attention: it is not a scale model. I simply wanted a functional model with which I can remove snow from my garden railroad. The base comes from a Bachman car an the housing will be mounted later on this. ... Prototype to check Function of the...

The body and boiler were printed before I builded a hot bed, so these parts can be printed with less warp. However I'm quite pleased with the result Some parts might still need a bit of finetuning but it was a fun project to work on. ...Here's a short...

I am constructing a prototype of a 2D-F1 Archbar train truck in a precise 1/20.1 scale model. My goal is to create various sizes of this truck, which will ultimately be utilized as logging equipment for my railroad. I intend to share updates on the...

Remixed from a 12-ton coal wagon, I scaled it up to suit the Bachmann Largescale Thomas the Tank Engine set we enjoy running around our Christmas tree every year. It's as large as I could fit onto my Malyan M150 printer. The dimensions are 190mm x...

Tank car for my 1:29 Scale Garden Railroad. End cap is a customized version of https://www.thingiverse.com/thing:953781. You will need: 3" (3.5" OD) Schedule 40 PVC pipe or 4" OD Aluminum "Air Intake" pipe (Print 4in alternative parts) or 4"...