fusion3 f410 3d models

... this ought to fit the bill and allow for some smooth enough spinning, until I decide to put some bearings into it. Noticed some other useful parts on the Fusion3 Group here, so thought I would throw this up in case it can be useful to someone else.

Print Settings Printer: Fusion3 F306 Rafts: None Supports: None Resolution: 0.15 Infill: 20% Notes: I opted for PETG filament as an insurance policy against warping if my box happens to be exposed to high temperatures - best of luck with your...

Print Settings Printer: Fusion3 Rafts: Doesn't Matter Supports: No Infill: 30% Post-Printing You'll likely need some kind of adhesive material on the bottom (I used craft foam) for optimal performance on hardwood floors. Consider printing it bigger...

... filament feed tension. It allows you to print upright without supports, making it perfect for tasks like quickly switching between different types and colors of filament - currently in use with a Fusion3 F306 3D printer to speed up the process.

The mask features horn variants from season 1 and 2 of the series. Print Settings Printer: Fusion 3 F410 Rafts: Doesn't Matter Supports: Yes Resolution: .2 Infill: 30 Filament: Atomic ABS white Notes: Any filament should work. ...Filaments that sand...

File is scaled to be the actual size of a cockatiel, feel free to adjust the sizing if you wish. Print Settings Printer: Fusion 3 F410 Rafts: No Supports: Yes Resolution: 200 Infill: 38 Filament: Atomic ABS Notes: Any filament should work, model...

The model should print fine at other resolutions too. Print Settings Printer: Fusion 3 F410 Rafts: Doesn't Matter Supports: Yes Resolution: .1 Infill: 30% Filament: Atomoic ABS grey Notes: Any filament should work with this model. Category:...

This is a remix of the original design I created...but without the added details!\nPrint Settings\nPrinter: \n Fusion3\n \n Rafts: \n No\n \n Supports: \n Yes\n \n Infill: \n 20%\n \n Notes: \n Printing separate components is highly recommended, as...

Print Settings Printer: Fusion3 Rafts: No Supports: Yes Infill: 20% Notes: Supports are essential for the main body, but not required for the wings, which print flat. Post-Printing I printed the main body with gray filament and the wings with black,...

... a 300x300x400 millimeter or larger bed size. It might fit on smaller printer models, but that has not been tested.Print SettingsPrinter:Fusion3 F410Rafts: Doesn't MatterSupports:YesResolution: .15Infill:30%Filament:Atomic ABSgrey  Category: Costume

Parts bin: https://www.globalindustrial.com/p/shelf-bin-nestable-4-1-8-wx-17-7-8-d-x-4-h-blue Small Bin: https://www.globalindustrial.com/p/little-bin-plastic-stacking-bins-1-3-4-x-3-1-4-x-3-blue printed and a Fusion3 Edge .6mm nozzle .3mm layer...

... made the planter waterproof. After sealing the model, I proceeded to add a vibrant coat using acrylic paint. Print Settings: Printer: Fusion3 Rafts: No Supports: Yes Infill: 10 Notes: **See note about infill setting under the summary section**

... of a chamfer on the bottom and relief for lanyard attachment. Print Settings: Printer: Fusion3 Rafts: No Supports: No Resolution: 0.2 Infill: 30% Notes: PLA and ABS materials have proven compatible, yielding excellent results in printing trials.

Print Settings Printer: Fusion3 Delta Printer Rafts: Yes Supports: No Resolution: (not sure, I have a .4mm nozzle, layer height .3mm) Infill: 15% Post-Printing Use a file and pliers to clean the parts. You might need to file the socket where the...

Get those here: http://www.thingiverse.com/thing:1375575 Print Settings Printer: Fusion3 F400-S Rafts: No Supports: No Resolution: 0.25mm Infill: 25% for small parts and 15% for large parts. Notes: I used such a low resolution because the parts are...

The orbital rings can be installed after printing once a mesh material is placed over the eyes. Model is already scaled to fit an average adult head, feel free to scale it to your own comfort! Print Settings Printer: Fusion 3 F410 Rafts: No...

Timelapse of the print: https://youtu.be/XvIGYAJ2jyc Print Settings: Printer: Fusion3 F400-S Rafts: Doesn't Matter Supports: No Resolution: 0.25mm Infill: 25% Notes: These are designed to print without supports in the orientation seen in the part...

Printed with support. ; toolchange from [current_extruder] to [next_extruder], layer [layer_num] {if current_extruder != next_extruder} ;before tool change M106 S0 ;turn off fan G92 E0 ;turn off retraction G1 E-0.8 F2100 ;retract G1 Y100 F12000...