fusion3 f410 3d models

Handy tip when swapping out the conductive tape on your Fusion3 F410 printer - use the length of the part itself as a marker for aligning it perfectly with the glass bed.

I ended up snapping my spring pre-load on my Fusion3 F410, so I opted to forgo waiting for the replacement that's currently en route, instead deciding to fabricate one myself. This custom part is a precise replica of the original Printer OEM...

Fusion3 F410 Extruder side plate: (Blue Part in picture) First let me say Fusion3 is a great company with super Customer support. Ordered the replacement and was there the next morning for me. I did this design because all the internals were still in...

Broke my spring preload for my Fusion3 F-410 so decided to make my own while they shipped me a new one. ...(exact replica of theirs)   This is a Fusion3 design (I do not own the rights to this design, it is a replica)

Allows you to adapt off the shelf Miele HEPA/Carbon filters to the Fusion3 F410 Printer. ...If there are requests I can see if I can modify for standard fan sizes.

Fusion 3 anti wobble. Used on front left lead screw. ...Snap in place, raise bed and gently lower onto screw.

some how my boss managed to break the whole assembly so i took it opon myself to fix it. ...i made some slight modifications to the original extruder housing and then designed the face plate for it and everything thing fits very well.

The strings on my printer broke again, so instead of purchasing replacements I figured out how to convert it to belt drive. Replace the string pulleys on the steppers with the 30 tooth gt2 pulleys. Replace the four bearings in the back with the...

This is the rear feeder fixed to take the V2 Bowden tube. ...

Replacement filament feeder for the Fusion3 F410. Made as close to the original in the amount of time I had. Prints perfectly with no support and about a 30% infill. ...I would not go lower than that.

This is a customized Universal Spool Roller, designed specifically for the wider 2kg spools from filaments.ca (+/-147mm width) in the Fusion3 - F410 printer. Note that the width of this completed piece has been carefully crafted to fit snugly within...

The stock extruder on the Fusion3 F410 has been the bane of my existence. I finally decided to upgrade to a bondtech so that i'd never have to worry about it again. I went with the Bondtech QR 1.75 Righthand extruder (SKU: EXT_UNI_1.75) I...

BQH2 on a Fusion F410

We've created a direct replacement for the extruder clamp on the Fusion3 F306. ...To protect our fingertips, we redesigned the clamp to eliminate those pesky finger tip torture springs that held the extruder clamp in place.\r\n\r\nTo print the clamps,...

Here's a front filament guide for Fusion 3 F410 extruder. It was printed from nylon to make it last longer. At the very top of this part, it tends to get too hot and turns into a mess. Printing a tower next to the part is a good idea to let it cool...

Here's a rear filament guide block for F410 extruder, I selected nylon as the print material due to its lubricity properties and longer lifespan. A solid layer blocks the through hole from top to bottom. This design requires the printer to bridge the...

Hardware: (1 ea) Printed Parts (4) 10-32 x 1/2" flat head machine screws (1) HEPA Filter #86880, #40320...

I went to Fusion3's website and found that I had to purchase the entire mechanism with stepper motor for $160. So I reverse-engineered the part and 3D printed this on my uPrint SE Plus. The Fusion3 F400-S has never worked better. The part...

This is a compatible replacement filament feed hatch designed specifically for use with the Fusion F410 3D printer. ...The two locking tabs on the original hatch had broken, rendering it unusable.

We have a Fusion F410 3D printer at work and recently, the bowden tube kept slipping out of its clamp at the filament end. To fix this problem, I decided to boost the surface area of the clamp, thereby tightening its grip on the bowden tube. ...This...

Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647

Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647

This is a primary attachment point for using a Tunnel Filament Gauge on a Fusion3 F306 printer. The Tunnel Filament Gauge is designed to identify filament feeding issues caused by filament blockages or running out of filament completely. You can...

Preliminary Mounting Arm Installation Guide for Tunell Filament Monitor on Fusion3 F306 Printer. The Tunell Filament Monitor is specifically designed to quickly detect filament feeding problems caused by either a jammed filament or running out of...

This guide block takes the place of the sponge that comes installed from the factory. Its purpose is to direct the filament onto the sensor wheel, where the sponge fails to do so and can wear out the funnel in the front guide block, causing the...

I've uploaded what's probably my third repair part for the Fusion F410, and I'm hoping this one will finally get it right. The original part had its layers oriented horizontally, which made it a ticking time bomb - just waiting to break along those...

We have a Fusion F410 at work and have had several issues with it over the last two years, particularly with the 3d printed parts. We recently had a rash of feed errors only to find the plastic wheel was grinding against the encoder base and filling...

There are 2 versions, one is split up the other is not The full version (AC Air Ramp V3 Full) was designed to be printed on a Fusion3 F410 which has a build volume of 14in x 14in x 12.4in. ... The other version (6 "split" files) are split up to be...

At one point I was working with my friend who made the mistake of buying a Fusion printer. I was in the process of designing an improved 360 degree fan duct and some other improvements and was going to try to convince him to let me convert it to dual...

This clip that came with my Fusion 3 was complete crap and split with low amounts of force. I have made a similar dimension clip myself in Blender that is much more durable and shouldn't break under similar (if not more) amounts of force. ... The V2...