fusion 360 models

 It is recommended to use MERV13 or higher for virus carrying particles. The fan is a Black & Decker 9in Mini Box Fan, Model BFB09W*.CostAt the time of writing this the total cost is the same for each of the 3 versions as the different...

It's worth the trouble to get access to a laser cutter to get cut panels.  The duct is intended to print at a 45 degree angle - the part model is oriented as it is intended to be printed. The duct part DOES NOT NEED SUPPORT. Your slicer may...

Check out the Raspberry Pi 3B+ here: https://www.raspberrypi.org/products/raspberry-pi-3-model-b-plus/ The controls are simple but there's enough buttons for most games. D pad for direction control and 4 front buttons provide your basic SNES type...

Some LED displays (3 digit, common anode, 0.4 inch, row pitch of 12.7mm) -Wenrun 12.7mm LTD040BUE-101A red CA -Wenrun 12.7mm LTD040BAG-101 green CA -SunLED 12.7mm DUY10A3-A yellow CA -SunLED 12.7mm DUG10A3 green CA -Luckylight 12.7mm KW3-401AVA...

The first one was a box, with an RFID reader, that provided clues on its LCD screen and had a secret compartment that opened with a specific secret code. The second device was this Bocca della Verità with RFID in the mouth (it was a secret) provides...

If in doubt refer to Mehdi for more demonstration material.I was basically trying to address two "issues" of my Anycubic Vyper:The PSU and Mainboard 24V fans are very loudI want to upgrade my Vyper with an OctoPrint/OctoPi setupSo here is my...

If using liquid electrical tape, allow it to cure before continuing. Gluing Use a small amount of hot glue to attach the diffuser to the LED mount. Using To use, simply attach a 9v battery and insert the LED mount into the base, ensuring that the...

There were points where I’d get 0.4 and Edwin would be 0.5 with his ruler while using the same model. Chances are that we used a ruler that was slightly wider than what 1mm is in reality.</p><figure class="image image-style-align-center...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

- You can find a somewhat more detailed list of supplies in my Instructable: https://www.instructables.com/Kissing-the-Frog-V20-Back-Horn-Bluetooth-Speaker-F/ Any combination will do (as long as the driver is 4" or smaller so it fits the enclosure -...

3D printed parts: 8 brackets, remixed by me and provided here (original design: https://www.printables.com/model/200616-creality-ender-6-enclosure-top-cover-lid-2020-240m) 3 door handles (https://www.thingiverse.com/thing:4768759) Shortened spool...

El porta filtro es removible y puede ser sustituido por otros modelos con anclaje tipo 3M.(The filter holder is removable and can be replaced by other models , fit some 3M filters) Este es mi primer aporte contra la lucha contra el coronavirus...

On homemade springs using generic musical wire When it comes to homemade magazines, the models by Thanhtacles are designed to use drum springs unlike the box springs exemplified by their commercial counterparts, for what I assume is the most...

Dimensions: 510 m × 330 m × 241 m Model scale: 1:3x103 (15cm) 1:8x103 (7cm) References "Lawrence, K. and Benner, L., Radar shape models of asteroids compiled by Lawrence V1.0. urn:nasa:pds:gbo.ast.jpl.radar.shape_models::1.0. ...NASA Planetary Data...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

One important note is that I specifically modeled the pistol's grip to fit the exact CO2 bike pump specified. Theres no guarantee it will fit similar Bike pumps as I took measurements from the exact one I have. DISCLAIMER: By downloading these...

Of course, the main one I use so far is Cura, and nevertheless I am increasingly discovering interesting and, most importantly, easily implemented printing methods. In this model, I combined the world-old technology for assembling rectangular...

You might also want to clean it with alcohol or antibacterial soap, on occasion, depending on your preference.While this design is Creative Commons - Attribution, I would ask that anyone who wants to sell this to other people take all precautions...

Comments and suggestions are also very welcome.Update 2020-10-19 Kermi radiator mount clips now availableQuite a few new MultiClip Objects in the collection (link above).Update 2018-09-21 Updated the alignment helperNew: MultiClip Glue!Update...

The Raspberry Pi controller has a radio module attached to it for issuing commands, though I used the slightly different NRF24L01+PA+LNA model which offers better range. You could also use the same NRF24L01+ module as the puck uses, the wiring and...

The lamp stand, lamp shade and the bases of these two parts. The models in the STL files have the correct orientation. All parts are printed <strong>without support</strong> and with a layer height of <strong>0.2 mm.</strong><br/> Use an...

IntroductionMany designs like RC cars and trucks, lanterns, model houses, etc. would benefit if 3D printing could be used to create truly transparent window panes. But as you might know, FDM printing transparent filament per se does not result in...

...I propose some activities to do programming this robot: First goal: Making it move The first and basic activity could be to program and model their movement, to find the correct position sequence for each leg for a forward run. First step: assembly.

-This current model is built under the assumption that most people will be using this with old tablets (or phones) that they would have thrown away otherwise, so taking a tablet (or phone) off of the top slider isn’t a smooth and seamless experience...

- You can find a somewhat more detailed list of supplies in my Instructable at https://www.instructables.com/Kissing-the-Frog-V20-Back-Horn-Bluetooth-Speaker-F/ Basically any combination will do (as long as the driver is 3.3" or smaller so it fits...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

I suggest printing samples of just the top 20mm of each model to make sure they fit before printing the whole tower. 3rd UPDATE: I've added a calibration print. This is a small sample of how the two halves of the v2.5 towers fit together. You can use...

Designed with the help of acoustic modelling software. Comes with carbon fiber slide, complete with PLA stockings.</p> <p>Also available in large bore version at <a...

... broken and no one is going to fix it. Download files one at a time by clicking Download each time. ### My some other things: Category: 2D Art

Also, I am considering some re-design of the right motor plate that currently interferes with the model fan duct. That would recover a bed Y-dimension back to 220. So, after all the print area will be 210x220mm... Parts to print: all parts at last...