fursuit ear pattern 3d models

Intended for Leopards but can be modified for other cats Scale: depends on your slicer. ...430% works ok for me Infill: 30-50% needs to be strong Supports: yes Print time: should be around 24hrs on good settings

print at 420%-450%. Supports are necessary. ...Print nose-down to save time You can sell prints with attribution!

Print at 420%, PLA+ or ABS works best. ...Eyes should be printed at 410%

Ho creato questa targhetta personalizzabile tramite Autodesk Fusion 360 di modo che possa essere personalizzata col proprio nome a piacimento. ...Basta scaricare Autodesk Fusion 360 e mettere il proprio nome.

Based off of Wickerbeasts, an original species Scale: 470% works ok for me. Make sure to compare it to a file you know fits you! Infill: 30% or higher Supports: yes! Foamwicker is intended for making expanding foam molds. ...

Provided by a commissioner on my Etsy! Thank you to everyone who buys custom models, as it helps the community and allows my business to keep running. Print base and teeth at 420%, support is needed. ... Fits the "shorthappyeyes" available in my...

This remix I made because I needed a feline teeth set but I couldn't find one I liked. ...It's intended for a feline such as a house cat but you could use it for pretty much anything

Based off of a Wickerbeast but can be modified. Scale: 470% works ok for me. Make sure to compare it to a file you know fits you! Infill: 30% or higher Supports: yes! Foamwicker is intended for making expanding foam molds. ...

This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/dkzWdVPPuTD Use the four smaller holes for bands connected to a servo motor, to wag the tail. ...middle hole is for metal wire, to allow the tail to be semi rigid.

* this model is not properly scaled. I'll update this with the proper scaling as I find out, but if anybody knows and wants to leave it in the comments that would be great. Teeth model is by DocCopemys! You are free to sell blank prints and...

These are the current official eye blanks of Frosti Had Sundae and used in all my costumes. Size is to scale. TOS: Personal Use only! You may use them in commissions, but do not sell the eyeblacks themselves! Do not steel and resale any of my 3d...

This will probably be my last free model. Between the model theft and having to visit the library for each model, I can't support it anymore. All of my new models will be posted to Etsy for $10, a minimal fee compared to most vendors. ... load in...

i just made them shorter

This base is intended for lions but can be modified for other big cats. ... Scale: 10000% Infill: High, 50-80% Jaw set and Hinges not included Some edges will need sanding before use

Intended for dogs but can be modified for other animals Scale: %10000 Infill: high, 50%-80% Make sure to sand rough edges before use

A custom-made eye rim designed specifically for cartoon-style fur suit heads is now available. It needs to be printed with precise dimensions: 3.5 inches in height and 3.75 inches in width, along with a depth of 1 inch. ...The wall thickness should be...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

haven't tested it yet but I plan to use this in a mask.

print at 420-440%, supports will be needed. The base was modeled to be a moving jaw mask, but it can be made static with a bit of adjustments and foam. Fits the kemono eye style, available in my etsy shop (eye pack #1) you may sell raw prints...

This shark base turned out rougher than I would have liked, especially with the teeth. So instead of selling it on etsy, I'm going to put the model on here for free. ...Have fun!

Another unusual species added to the roster.

This is a Crow Head I 3D modeled. Its designed for a head that is 172mm wide (Max) and padding is required at the back of the head (Foam is recommended). Using a 3D pen to weld the edges of 3D glue is recommended. The STL files are cut to fit a...

Remixed from: https://www.thingiverse.com/thing:4338146 Took the file, put it into Microsoft 3D builder and subtracted it from a box. Great for mold making in silicone, foam clay or even skulpy. It will need a release liquid medium of some...

This is a pivotal connection point where the Lion head interfaces with the jaw, securing them together seamlessly. ...The slotted edge of this component fits snugly into the jaw, while the smooth surface aligns perfectly with the head on the...

these guys are my own little original species. It's an open species so feel free to go nuts! I don't have a lore page yet though, so sorry guys. The eyes are electric, and they have like a metal helmet thing. ... 420% or 450% scale, inches

eyes used: https://www.thingiverse.com/thing:4359645 hiya!! finally another thing i made. ...Will update it when i have the time

A set of toony teeth I designed for one of my heads. ...Includes a canine/fang, lower teeth and side teeth that can be installed on the top or bottom jaw (or both!).

This model was built using Tinkercad. ...Make adjustments right here - https://www.tinkercad.com/things/5q7mZVWpQ6k