funny qr codes 3d models

Not a vectric, not a bitmap file, not a G-code. You buy a digital model image file for the manufacture of the product, and not the product itself as a physical unit of goods made of glass or wood. All copyrights to these hosted models belong to...

If you are interested in checking it out, use my referral code to get an extra 5000 aUEC in-game currency: STAR-2Z59-G9CS The desk consists of an upper deck in the back, and a lower deck in the front (closest to you). The PC enclosure is suspended...

Both uploading and downloading a few dozen bricks is a pain :) However you can get all: STL.zip contains all the blocks I made so far STL-sets.zip include multiple brick sets for printing (difficult and not so often updated !) source.zip contains all...

A clamp also works wellI included STL for all versions of every partG-codes included for glued version (Modular)Assembly Screwed version:You will need 12x  6-32 screws 5/8 long (7/8 long for the old version frames) this length works with...

Compare them to yours, and if there are differences, consider implementing them into yours (especially if you get “Move out of range” errors).[stepper_x] step_pin: PC2 dir_pin: PB9 enable_pin: !PC3 rotation_distance: 40 microsteps: 16 endstop_pin:...

If you're lucky, you can adjust these values to suit your negative carrier; however, the edges of the mask are beveled, and if your negative carrier requires another type of bevel, or some other change, you'll need to adjust the beveling in more...

Not a vectric, not a bitmap file, not a G-code. You buy a digital model image file for the manufacture of the product, and not the product itself as a physical unit of goods made of glass or wood. All copyrights to these hosted models belong to...

Therefore stop needs to be inserted in the G-code.In prusa slicer inserting stop it adds the stop at the beginning of the layer so it should be added at the instance where magnets are being covered.Print and insert magnets. Make sure magnets polarity...

Code and other build resources here: https://github.com/Rad-Bench/flux Parts list: 3D printer: [Voxelab...

Not a vectric, not a bitmap file, not a G-code. You buy a digital model image file for the manufacture of the product, and not the product itself as a physical unit of goods made of glass or wood. All copyrights to these hosted models belong to...

Not a vectric, not a bitmap file, not a G-code. You buy a digital model image file for the manufacture of the product, and not the product itself as a physical unit of goods made of glass or wood. All copyrights to these hosted models belong to...

Not a vectric, not a bitmap file, not a G-code. You buy a digital model image file for the manufacture of the product, and not the product itself as a physical unit of goods made of glass or wood. All copyrights to these hosted models belong to...

To make sure you end up with a printable model you will not be allowed to render if you have not checked the highResolution box (or set the variable to true if you are editing the code) or if you have selected renderMode 0. Sanity checks There are a...

The wiring of these terminal strip equipped units must be conducted via wiring methods laid out in NFPA 70 / NEC Code Book Article 500. This unit is a factory sealed fixture.Adjustable Surface Mount Brackets: Each L-shape bracket is machined with...

Design make it able to do a lot of rollover/flip witouth breaking I use Esun PLA+, Esun PETG, Esun Elastic TPE 85A G-code included for -Prusa MK3S+ with standard 0,2mm quality, filament setting Esun PLA (standard) and prusament PETG...

Print time is about 9hrs 45mins, and uses about 90g (30.5m) of filament. Printer: Prusa i3 MK3S Rafts: No Supports: Yes, but on baseplate only Resolution: 0.2mm Infill: 20%-25% Perimeters: 2 to 3 After printing, one of the long M3 screws can be used...

Not a vectric, not a bitmap file, not a G-code. You buy a digital model image file for the manufacture of the product, and not the product itself as a physical unit of goods made of glass or wood. All copyrights to these hosted models belong to...

The length of the screws depends of you setup, the case measure 30 mm.  12mm Push Button Switch - https://www.aliexpress.com/item/32896221862.html?spm=a2g0s.9042311.0.0.27426c37R7cspc 2 Micro switch for the shifters -...

Could not find a simple library for DS1302 so I wrote code. *** Update 07 Feb 2021 *** V2Files.zip has all new files compressed. Version 2 hardware and firmware changes : - STM32 internal RTC is used. Blue Pill hardware has a 32768Hz...

Much of the process after cutting out the segments will be the same. The software I'm using to run the sceptor is available at via the online Arduino Editor here Parts LED RGB Strip - Addressable, Bare (1m) OR LED RGB Strip - Addressable, Sealed...

In this case it is important to centre the spring to the positive 18650 battery terminal, which my other adapters exhibiting a cone do (see cutaway view).As always, I include the OpenSCAD source file for you to adapt and/or improve:Download and...

Not a vectric, not a bitmap file, not a G-code. You buy a digital model image file for the manufacture of the product, and not the product itself as a physical unit of goods made of glass or wood. All copyrights to these hosted models belong to...

                  if you have higher print, you will spend more time with printer                    ??            ...

* Revised 'rudder trim lever.stl' and 'elevator pot gear.stl' with a 2.5mm diameter holes added that can be tapped for a M3 grub screw to secure the lever to the potentiometer if required 3rd January 2021 : Mounting plates, Fritzing wiring diagram...

Why not combine the two things to have a fun little robot friend who drives your 3D printer AND says nice things to you??Introducing; BMOctoprint! All the 3D printable files can be found here; additional files like animation and code can be...

Not a vectric, not a bitmap file, not a G-code. You buy a digital model image file for the manufacture of the product, and not the product itself as a physical unit of goods made of glass or wood. Non-commercial use only. ...Attribution-NonCommercial...

(Alternatively, you can check out a fork of the code that allows for a photoresistor by @RJFeddeler https://github.com/RJFeddeler/7-segment-clock) Join the back pieces using the nuts and screws Solder the SN74AHCT125N level shifting chip to the clock...

After using metal files for years with just their tangs for handles, I decided it was time to create & print a set with my new Prusa i3 MK3. Naturally, I chose to use wood filament for the prints... :-) A few alternative uses: You can always...

Not a vectric, not a bitmap file, not a G-code. You buy a digital model image file for the manufacture of the product, and not the product itself as a physical unit of goods made of glass or wood. All copyrights to these hosted models belong to...

The wiring of these terminal strip equipped units must be conducted via wiring methods laid out in NFPA 70 / NEC Code Book Article 500. This unit is a factory sealed fixture.Adjustable Surface Mount Brackets: Each L-shape bracket is machined with...