funny fruit photos 3d models

In the photo, the blue NOR gate has inputs of 1 and 0, with an output of 0, and the white NOR gate has inputs of 0 and 0, with an output of 1. How I Designed This A functionally complete set of logic gates is a set of gate types that allows one to...

You will need a 3D printer. The Z stage does not use a servo, as in Misan's machine, but rather one of those cheap 28BYJ stepper motors you can find for 1.50$ on eBay. NOTE: The photos are of the current prototype, some of the modifications to the...

Might I suggest a Raspberry Pi 3 with Octopi installed?Octoprint "GCODE Scripts"After print job is pausedM117 Print Paused{% if pause_position.x is not none %} ; relative XYZE G91 M83; retract filament, move Z slightly upwards G1 Z+5 E-5 F4500;...

See description for more details.2024-01-24 - Added more printing tips for drawer, and recommended print orientation photos.What are the features of these boxes?All storages are made of a box, and a drawer. Each drawer can usually fit 10 loose games...

All parts will print without supports or brims positioned with the flat side down and the opening of the body up (See attached photo). It's important that your printer is tuned as well as possible.Assembly Instructions:After printing, use a 2mm Allen...

Like I said above, everything painted in the photos is from Town builder. You can make simple buildings. You can make huge dioramas. And you can make anything in-between. This is all printed on a FDM printer. I used a couple coats of Mod Podge to...

Great for taking surreal photos with simple props, or simply shedding light on the subject. Print instructions Concept: Running power through a 3D Printed part Simplest Solution: A bare copper wire Proof-of-concept: An LED Track light Combine...

Therefore I only report the basic steps to do this, without photos. Compatibility with the Genius and the new X2, I don't have a Genius so I couldn't check the compatibility, but you can try and warn me, instead for the X2 even if I haven't done any...

If someone has a high speed camera, a cool video could definitively determine the cycle rate.Late Breaking Reliability DataI just discovered a failure.  The upper gun in the cover photo was printed with translucent green ABS.  I had reduced...

I have had a prototype printed (see photos) which mostly worked, and I have improved upon it, but this latest iteration of the design is untested as I do not have my own printer. Help me win one by Liking it, assuming that you do actually like it. I...

**"How can I get started?"** For the build shown in the photos above, I used this $25 full-range woofer from Parts Express. I chose it because it was cheap for experimenting with and this particular speaker actually has some very good specs for it's...

The parts in the photos above are printed with Prusament PETG Galaxy Black.Guard_Cover_Front_MULTICOLOR_0.2mm_PETG_MK3S_1h11m.gcode will print a dual color front cover without the need of a MMU. ...Start printing with the color of the inlay, there will...

The construction costs are about 300€ and the construction time is about one day. contact email address ownplant@gmail.com Print instructions1.) Print out all parts and insert all thread inserts 33x "M4 Thread insert" they are all the same 2.) Saw...

You can see examples of those dents in the photos if you look. I found that sanding down the most prominant ridges in the mould mitigated much of the issue. [UPDATE] I have managed to crack one of the moulds during clamping. It can be repaired with...

(I took a photo so I didn’t forget). Bed Thermistor connects to "T1". https://cdn.thingiverse.com/assets/49/9a/d5/d9/2d/2021-02-24_14.28.59.jpg https://cdn.thingiverse.com/assets/f9/98/71/de/3e/2021-03-13_19.33.27.jpg <b>5/</b> Install KAD...

... convenient to use some kind of plastic lubricant between the two gears.In this step you have already completed the construction of your Darrieus Wind Turbine. It is convenient to fix the legs with double contact tape to a base as shown in the photo.

Also, the photo is of the prototype. The current version is a major redesign that looks about the same, with one notable change being that I tightened up the tolerances so the knife panels will not have the large gaps. This is my attempt at making...

These are in design rather than print orientation, and will load in context with the sundial set to its 90º rotation (sundial_mainbody_90.stl).Other detailsFilaments shown in photos: Polyalchemy Elixir Copper, Jessie Green Ice from Printed Solid,...

With a little luck, this lands the legs on the grooves inside, and you can use a flathead screwdriver to bend them down into place.Roll it up and slide the hexagonal latch on to the track between compartment A and F.Take a photo of your competed Hexx...

NOTE: I'll include photos of the board once its done, currently I just have parts so think of the current instructions as my plans. Ill update them and remove this note once everything is together!</p><p><strong>Story</strong>: I've been skating...

... If you are reading this: Awesome! I wish you good luck with your project! I hope this was useful. If anything seems wrong write a comment please. Have a lot of fun with your cute toaster! :3c Cover photo: [vlakovlk](https://linktr.ee/vlaaacek)

After conversion, my X-MAX is ultra quiet (thanks to TMC2209 drivers), prints up to 170-200mm/s with great print quality, uses inductive probe as endstop and auto Z-offset, has a camera feed and web interface (Mainsail).&nbsp;Some photos of the...

As illustrated in the photos above, the series of mounting holes at the top of the bracket enable this explosion proof LED light to be attached to any wall, ceiling or floor surface. A simple through bolt can be used to secure the light to the...

As illustrated in the photos above, the series of mounting holes at the top of the bracket enable this explosion proof LED light to be attached to any wall, ceiling or floor surface. A simple through bolt can be used to secure the light to the...

Drop both of the into the cavities in the caddy.Fold the excessive ribbon cable as shown in the picture.Cover the lids onto the adapters and screw them down with 4 sets of M2x6 screw and nut.If you ended up with more slack with the ribbon cable, try...

The photos show a comparison of my 55° mushroom test (https://www.thingiverse.com/thing:2005832) on a PLA print between this duct, the v6 dual duct, and the stock duct. The result from the stock duct looks more decent than what I expected while I...

The key trick to know is that, unlike stitching a sequence of photos taken by moving the camera and lens, your images shouldn't really have any lens motion. Thus, you'll want to tell Hugin that you used a lens with a relatively long focal length, so...

Note that the top reel's grooves should fit toward the bottom reel's grooves; see the photos. If your build plate doesn't release objects easily, be very careful when removing this part; it's easily damaged. Next, print the...

- Flexible cable conduit (for the top level, see the actual prop photos) - Misc wiring (for all over) - small Zip ties (for all over securing the wiring etc) - Optional (If you want more strength on the top rods): 2x 3mm Tubes or dowels (200 mm...

(Refer to photo of T800 for how to measure the size you will need to print) Just scale in your slicer software on XY by 1/58*[your figure].Do subscribe to my YouTube channel. Stay tuned on the latest build videos.</p><p>All constructive comments and...