funko pop wall display 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

Then when you sandwich it all together, the leads will expand out towards the walls of the base and not in a wuzzle. Note: If using the lamp base with switch, slip the edge of the processor plate under the box that holds the switch first and then...

I recommend a minimum of three walls/tops/bottoms and 25% infill. Included are the following files: marshmallow_43ID_1-25in_breech.stl - The piece as seen in the pictures, 31mm breech length. Aside from the locking tab all other angles are 45°...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be removed from the brackets by removing the set screws that hold the bracket to the mounting bracket and adjusting the fixture. The fixture can be adjusted at...

I 3D modelled and printed some end caps for it with Ninjaflex so it doesn't scuff up my walls. 4/10 update: I added some parts that hold a 3/8" steel rod in the middle of the pull up bar so it isn't just relying on the screw coupler to hold the...

Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be removed from the brackets by loosening the cap screws that hold the bracket to the mounting peg.Suspension Mounting: Pendant mount fixtures hang from the...

One could also try one of those heat resistant PLAs (after annealing/crystallization), yet they may deform due to the thin walls during annealing. - nf_crazy_cable_holder, filament_sensor_holder, nf_crazy_fan_duct -> can all be printed out of...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

Some sanding may be required. Other Requirements:Sandpaper or chiselSuper Glue (Optional but recommended)  Print Settings I used: Cura settings for Creality Ender 5 Plus - Standard Quality  Layer Height: 0.2mmPrint temp: 200...

Mount it on the wall! easy to print and assemblewith the provided gcode and printing instructions you can't fail. The system uses minimal supports and is assembled in minutes</li> <li><b>Use parts you already have</b><br/>The Spool holders use parts...

In addition, LEDs are also safer for the environment as they are 100% recyclable, which eliminates the need for costly special disposal services required with traditional gas burning and arc type lamps.The remote controller has a range of up to 150...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 shape =...

Do not remove all of the print line texture by sanding as this will thin the walls and weaken the Nose. Your goal is to get the shape and profile desired for the final part. Take your time on this step as this is the foundation of the final finish. ...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

To avoid soldering on the V4.6 mainboard, an external PCB can be glued next to the mainboard (on the wall where the flex PCB is located).The PCB itself can be produced using the attached gerber files by JLCPCB, Aisler, PCBWay, OSH Park, ...Please...

I used the "29MM X 34" THICK WALL TUBE" from Apogee (part 10251) but others should fit. For a retainer I used the "29MM ESTES RETAINER", also from Apogee (part 24020) but again, others will work.You will also need shock cord, of course. I used...

- Reduced wall thicknesses and bottom thickness for faster printing and less materials. - Added optional mount point for DB25 breakout box for replacing extruder wire bundle with HD15 cable. More on that project later. - Added an optional dual...

Http://www.Thingiverse.Com/Apps/Customizer/Run?Thing_id=507810 Instructions Using the Following Options: Custom_phone_width = 100 custom_bottom_fillet_resolution = 8 printer_tolerance = 0.4 stencil_vertical_position = 50 custom_case_pattern_thickness...

This is also why you want to make this piece have strong walls and top/bottom. Once you are happy with the t-slot and cap fit, remove them and slot them into the cap piece with some super glue or epoxy, or whatever works best with the material...

But then again, these models are really unlike your typical vase mode prints in many ways!Though they can be printed with a 0.4mm nozzle, if you want, you can go all the way up to 0.8mm with the same level of success.For best results, use the...

Some reviews online criticized the strength of the double sided tape that comes in the kit so I used Gorilla wall mounting tape. Still some cable management to be done, I'll probably print something that will hold the wires above the fans. It does...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 shape =...

Magnet can slide up and down to lock and unlock.In order to lock/unlock you need to use magnet externally next to the wall and move it up and down. Depending on tolerances if it's loose you can hear magnet get to its limiting position. You will need...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...

 It uses the following settings:PLA for all parts but the latches, which are set up to use PETG0.4mm X1 Carbon profile3 WallsArachne wall generator 12% gyroid infill (base, modifiers are included which range from 15-25%)No SupportsBrim on several...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

These are located in the walls of the grenade halves and in the piston heads and must be perfectly aligned. Now insert your AEG spring into one of the pistons, put the middle ring over it, close it so that all holes are aligned and tighten the...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 height = 15 shape =...

 I recommend 4 perimeters (outer walls) and 30 percent infill.  The Table-Top Pieces can be printed right-side-up or upside-down, whichever you prefer.  Either way, use supports. (about 6 hrs and 73g filament each x 8)  If you prefer, you can use...