funko pop wall display 3d models

Like his predecessors, he possesses the Staff of Time, a powerful artefact inherited by Tesevros the Wise, who let the grandmaster of the Order to move the walls of the labyrinth at will, making any attempt to steal or destroy the ancient scrolls and...

Remix or modify however you want.Print NotesBladePrint the base of the blade with a high infill % and thick walls. The thin part of the base is under a lot of stress from carrying the rest of the blade.<br><br><strong>•Hilt</strong><br>There are two...

Print Settings Printer: FLSUN SuperRacer Rafts: Doesn't Matter Supports: Yes Resolution: .2 mm or .3 mm Infill: 30 Filament: eSun PLA+ Purple Notes: Print with 4 walls for strength. I used supports but used Cura's support blocker to block the 4 on...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

There are a couple other editable dimensions in the spreadsheet if you want to adjust things like the wall/lid thickness, the recess depth, and the size of the lip for the sliding lid. The blue reference dimensions in this recess sketch are also...

Print Settings ------------------ I printed using ABS with 7 shells/walls, and 20% gyroid infill. All parts are designed to be printed flat on the bed with no supports. Assembly ------------- To assemble the MegaSphere, first start by...

(see photos) The heater cartridge was also sliding out a bit and caused a high temperature spot, you may want to take a look yourself.Changelog:v2: 2020/05/234010changed the angle of the duct to hit below the nozzle, not the tipchanged focal position...

Fix with a dab of CA adhesive The aluminum tubing is 4mm diam x 0.45 wall. I bought this via amazon, though it is out of stock now. Should be available at hobby stores.</p>...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

lateral shelf walls restrict the view. Due to the max. 5.5cm long threaded rod of the motor, only a small stroke is possible here, but usually this is enough to get a better overview. The whole thing should preferably be HomeKit compatible or...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: phone_model = 3 custom_top_inner_edge_chamfer_radius = .6 custom_top_port_corner_radius = 5 custom_back_extra_port_corner_radius = 5...

Version V003 should match this picture pretty well. The tips of the star should be touching the inner circle (mine was too small) The top surface is segmented, but they are all the same height (mine had a 0.5mm offset) UPDATE V002 The 45° segment...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 shape =...

If you slice it, you have to activate the function "recognize thin walls". You can also choose the duo color option. With that, you can print the bottom and top of the ring also with a transparent filament, so the light goes more to the sides ;) If...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

I made the Tuning Pegs with PETG because I tend to get better layer adhesion and strength out of my PETG parts and I need them to be able to hold the string tension (I also used increased wall count). I used PLA for the Medallion, because I had...

Place a finger between the Clock Casing wall and the Support Column and gently apply pressure while installing the nuts so you don't break the support column.    Install all 12 Spoke Connectors, then place glue around the notch and the end of each...

Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be removed from the brackets by removing the set screws that hold the bracket to the mounting bracket and adjusting the fixture. The fixture can be adjusted at...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: shape =...

The rocket parts are designed to have .18mm layers for .4mm nozzles, which with PrusaSlicers be a single wall width for the body tubes and nose cones. ### Step 1: Select Components. You will need a nosecone, body tube and fin can. Multiple body...

Slide the rack segment in in-between the two finger gear segments. As you close the fingers, the small tabs at the bottom of the rack segment will flex the side walls of the base apart, and then ultimately click into place in the side slots in the...

this way the 3d printed walls are less likely to flex. NOTE: Don't make the parts too tight because you could split some of the print lines if you're pushing the pieces in too hard.After everything is cut to length and fitted you can go ahead and add...

;) Print Settings and Tips ==================== Filament: PETG, PLA, ABS, etc Resolution: .2 recommended Top/Bottom Layers: 3 Perimeters: 3+ Infill: 100% Infill/Bridging Angle: 45° Bridge Flow Ratio: 1+ Skirt/Brim: Recommended Raft: No Support...

Just check my uploads and find the set you'll need.This is the 20.0mm set for 20mm dogholes.If you need any other types of bench dogs / stops / clamps, need some different dimensions, have some neat ideas or the like then drop a comment and I'll see...

If you are interested in testing mounts for different sized bottles, please contact me and I will make one to fit your bottle.Print SettingsLine width: 0.4-0.45mmLayer height: 0.20mmWalls/perimeters: 2-3Infill: 20% except Core Type A Center: Infill...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

Plus, though for cosmetic reasons only, it is advisable to use a single perimeter wall setting for the first &nbsp;layer to achieve a better readability for the ml indication. Both of these setting are made in the cap's 3MF file.<br>All STL and 3MF...

Depending on how accurately your machine is printing, you may need to reduce outer wall width or increase it. Some slicers have x/y compensation, use if you are familiar and know how to correct these issues with your own machine. As mine prints...