funcub ng 3d models

To get the new can format to fit properly in your Saab 9-3 NG Left hand drive. This can be assembled when the canholder is folded back in, if placed correctly(Outlet placed to the passenger) Check to see if you have 3 ears/tongues in your car. ... They...

This is a fast and dirty fusion 360 model based on the Micro Swiss NG direct drive. The adapter is made to allow the use of a 5015 blower instead of the stock blower fan. The print requires support. I used cura 5.0 with tree supports and it...

To get the new can format to fit properly in your Saab 9-3 NG Left hand drive. ... This can be assembled when the canholder is folded back in, if placed correctly(Outlet placed to the passenger) Only for personal use!!

This is a remix of the V13 NG Fan Shroud from Microswiss. I had already upgraded to a Voron Afterburner previously, and already have a 4020 Blower Fan wired in. This allows a drop in of that setup. No clue about print quality, speed, or any of...

I didn't like the BLTouch bracket I got with the NG as I felt the BLTouch tip was too low during printing. One print that went a bit weird and overextruded actually broke my probe! ... Adjusted it to raise the BLTouch probe tip by 1mm, so the Z offset...

To get the new can format to fit properly in your Saab 9-3 NG Left hand drive. ... This can be assembled when the canholder is folded back in, if placed correctly(Outlet placed to the passenger) Only for personal use!!

The Boeing 737-800 NG Airliner, specifically featuring US Airways' livery (only exterior with movable flaps and retractable landing gear), has a low detail design based on blueprints. While accurate in major dimensions such as length, height, width,...

Original was slightly too thick to use with the CR-10/Ender3 NG variant and would cause binding of the V rollers. Rather than thin it out, potentially losing some rigidity, I added notches to allow it to sit flush to the back plate.I printed flat...

I also uploaded one without the need for heat set inserts, if needed.I also uploaded my STEP file so people can easier amend the model to their printer models an needs.Printable without support.There is also a version vor the Ender 5 linear rails...

Airplane: Boeing 737-800 NG Airliner - Continental Airlines Flyer, Exposed Outside With Flaps That Can Move And Landing Gear In Action.\n\nCreated By Scaling Up Official Blueprints, This Aircraft Model Matches The Original In Every Major Dimension -...

This is a fast and dirty fusion 360 model based on the Micro Swiss NG direct drive. The adapter is made to allow the use of a 5015 blower instead of the stock blower fan. The print requires support. I used cura 5.0 with tree supports and it printed...

This is an interface plate created for the Micro Swiss NG for use with the Wham Bam MUTANT V2. printed at 0.2 layer height. You will need 5 x 3 mm threaded inserts that come with the MUTANT kit Two versions available. Version A: ...

I needed a BL Touch mount for the Micro Swiss NG so i made one. I used the original shroud screw for mounting it to. ...I also used some longer M3x12 screws with a nut to mount the BL to the adapter Offset i used was x -50 y -7 it rubs slightly when...

I first drew the piece, then printed it and used it to drill the two 2.5 mm holes on the back plate of the MS NG and finally tap 3mm, which leaves the first 'original' hole free. to properly fix the shroud. ... Fixing is done with two M3 screws and two...

This is a remix of the Micro Swiss NG shroud https://www.thingiverse.com/thing:5358828 for use with a 4020 blower fan. So, it is fully compatible with CR10s Pro V1 & V2 fan's. I also modified the top right side of the shroud to place the...

I was using https://www.thingiverse.com/thing:4742800 with stock ender 3 v2 but upgraded to Micro Swiss NG direct-drive and hot-end. I wanted to reuse the endoscope holder I had already and just mount it to this fan shroud. ... This endoscope is...

A model of a Tudor-style door and several windows for the 7-foot diameter NG tower. A set of interior stairs to the right and left also for the D7NG, incompatible with each other. All pieces must be printed from the chosen model. ...It will not be...

See the original creator here: https://www.printables.com/model/436006-ender-5-plus-with-microswiss-ng-cable-chain The original creator made these for a 10x15 cable chain that was purchased from Amazon. He used the closed version of the chain,...

Link: https://www.printables.com/en/model/417661-ender-3-v2-neo-y-axis-limit-switch-housing I moved the limit switch back 5mm which gave me back print area lost because the Microswiss NG has different nozzle position. it should be printed with...

Use this template as an outline and drill template to cut a plate from 6061 aluminum to fit a Big Tree Tech H2 to the linear rail plate for the Micro Swiss NG extruder available from their store. Drill the holes with a 3mm drill after using a...

After installing my Micro Swiss NG I noticed the wires to the heater and thermistor moved while printing. I was concerned they would eventually break. I found redpiyaya's cable support but didn't want to have to remove the V-slot wheels to...

So I was assembling the brilliant NG Design's Cable Chain, however, my cables were twisted in a different orientation than his example, so actually the Extruder and Stepper Motors' Cable goes below the Heated Bed one, which made me unable to use the...

So I was assembling the brilliant NG Design's Cable Chain, however, my cables were twisted in a different orientation than his example, so actually the Extruder and Stepper Motors' Cable goes below the Heated Bed one, which made me unable to use the...

I've already been using antibimmer's cable chain set on my machine, but recently upgraded to a MicroSwiss NG direct drive extruder/hotend, and didn't feel like printing a new bed of links. So I modified ianewby's hot-end mount to accept the voxelab...

Printer Settings: * Printer: Sharebot NG * Rafts: No * Supports: No * Resolution: 0.15 * Infill: 100% Notes: A support wasn't needed because I tried to make it simple, but apparently that's not enough. There may be a small defect, but it won't...

I carried this over with the NG, but I went ahead and used a M3 nut instead of washers so that I didn't have to fight to keep the hardware contained. So, this uses a slightly longer M3 bolt, then I tightened down a nut on each bolt straight to the...

Straight forward wire management links for an Ender 3 V2 with a Micro-Swiss NG direct drive extruder. I provided the STP files so anyone can edit them to their liking.&nbsp;</p><p>&nbsp;</p><p>You will need a total of 10 links. I used zip ties to...

I went linear rails on my Ender 3 pro with a MicroSwiss NG and found that I did not have a way to attach an endstop to the X axis. I made this Bracket to fix that issue. Not much to it. ...Has an optional Cap.Included are Solidworks Assembly files, STEP...

A little stamp I made to print initials on bread, cake, clay...I printed it with an infill at 100% to be sure it's solid enough in the clay.

Colors: 6 length: 200 mm width: 410 mm height: 920 mm