full size buster sword 3d models
668490 3d models found related to full size buster sword.thingiverse
It's not as wide as the actual buster sword from FF7, because you'd not really be able to hold it properly at all. But its still big. Optional 3rd blade section can be reprinted 100 times if you want to make it stupid long. I am updating it...
thingiverse
This is a pommel for a full-sized buster sword prop. Instructions to make the full sword are on YouTube at https://youtu.be/0eExFqLVNH0. The drawing for the foam piece dimensions is scaled down at 1:1.4 to fit on one page. ...If you want to use the...
myminifactory
Full scale Buster sword from Final Fantasy, print in 15 parts and construct, super awesome prop for costumes and cosplay! The Buster Sword is a weapon that first appeared in Final Fantasy VII and has since appeared in several other games in the...
thingiverse
"If everything's a dream, don't wake me." -Cloud It's the Buster sword! The design is from KaiLun, all I did is simply make it life size. I took out the handle so you can use a 2 inch diameter wooden pole or PVC pipe instead for extra stability. Cut...
cults3d
Here's a full size Scimitar style sword, I cut it into pieces for assembly. ...It isn't perfect but it's neat.
prusaprinters
I made this full size Gladius sword in Sketchup using my imagination and a couple of pictures of Swords from the Roman Empire. Should be somewhat correct in size but I've never actually checked what size they should be. The whole sword fits on one...
thingiverse
Using my imagination and a couple of pictures of ancient Roman swords as references, I crafted a full-scale Gladius in Sketchup. To ensure accuracy, I measured every detail, taking note of the proportions to get it right down to size. The finished...
thingiverse
Made them full size, cut up the parts into pieces so they could print properly, and added holes for 1/8" steel rods to go through the center. Print orientation: Print the blade pieces with the point of the blade upwards. This will use the least...
prusaprinters
I made my own interpretation of an Pirate Sword, mostly based on Jack Sparrows sword. I modeled it using Sketchup. This model will also fit togehter directly after the print due to me making the pins a little smaller than the holes.</p>...
prusaprinters
... little smaller than the holes. Will also be doing this to the older swords at some point. Post-Printing Glue all the parts together with strong epoxy and finish with some sand paper and a paint job of your choice. ...Good luck!</p> Category: Props
thingiverse
I created my own rendering of a Piemont Sword from the 1800s using Sketchup as my primary modeling tool. By intentionally designing the pins slightly smaller than their corresponding holes, I was able to achieve a seamless fit that enables the...
thingiverse
I crafted my own replica of a pirate sword, largely inspired by Jack Sparrow's iconic blade. Utilizing Sketchup as my design tool, I meticulously modeled each component, ensuring a seamless fit upon assembly - the pins being intentionally smaller...
thingiverse
_________________________________________________________________________ Model of the Master Sword from Zelda: Breath of the wild, modeled in fusion 360. The Blade is 950mm long, The blade have some keys so they stay align, most parts do not...
myminifactory
... It is really huge sword length of the blade is 140cm, hand guard is 5cm and hand with the tip is 35cm. So its full size is around 180cm +-. Recommended to cut it in 20cm long pieces for better stability. ...Less claps = better stability.
cults3d
Full size, single piece STL is included, along with a sectioned file that can be printed on even the smallest of resin printers. ...There is a 5mm hole running throughout the centre of the piece to allow you to insert a 4-5mm steel or aluminium rod to...
myminifactory
This is a sword from skyrim, that i modeled. all parts should fit on a 5in print bed. Glue (of choice) and a dowel rod will make this a great add on to any skyrim fan collection. ...I would recomend support on some of the parts but not required
thingiverse
_________________________________________________________________________ Model of the Rusted Master Sword from Zelda: Breath of the wild, modeled in fusion 360. The Blade is 950mm long, The blade have some keys so they stay align, most parts do...
myminifactory
If you want more information and to see it more closely, watch this video: https://youtu.be/Za5byBQs0I4 This is the sheath that goes along with the Master Sword I created here: https://www.myminifactory.com/object/20390 I created this sheath in...