fuel cell 3d model

If you want it without internal battery, I have designed this same model without the hole for the battery, remaining in measurements of 126x51x35mm, you have it here: https://www.thingiverse.com/thing:6016310 Required Components: - 1u Mini ZVS...

If you decrease the size of the model, you will end up with less than 2 layers which might decrease the integrity of the maze. You should be OK increasing the size, but the maze walls may not fuse in the middle using 2 layers. You'll need to...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 120-277V and 347V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Wiring: These LED light...

The COMPLETE Order of the Labyrinth bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The strong Minocs of the Order of the Labyrinth are the descendants of Tesevros the Wise,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

Tolerences are tight on this model and will require percussive pursuasion to fit a 2020 bar Base - print with inside pointing up, support the central overhang, the Ports section print as bridged ### PETG: Top- print with the inside pointing up, this...

There seem to be quite some error margin in production, if your model is a bit too big to fit, just sand off maybe .5 mm from the sides to make it fit.Completely(!) remove any filament remains inside the two enclosure parts.Fit servo into upper half...

The Tunnelplan Wind Turbine is a 1:10 scale model of an existing wind turbine. The diameter of the rotor is 2000 mm (20 meters) and the tower height is 1200 mm (40 meters). the max.ceiling height inside the house. Solution 4 energy...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

In short, it means that we will be using the Name Tag creator  to make the base (and thus be able to add text, image files, &c), and then create fitting covers and holders in this program. (A mixed approach is to also create the base with...

... The single-blade model can be reversed in most slicer programs to cut from one side or the other of the 120 film, as described earlier, in "Preparing This Tool." The OpenSCAD source file therefore lacks any provision to make this adjustment. ...

I was unaware that the MMU2S required changes to the extruder and almost decided to hold off and just install the SPA by itself, but I started poking through the assembly manual for the MMU2S and realized there were changes that needed to be made to...

This write up is very comprehensive and written for someone who is not very experienced with 3D-printing/additive manufacturing. For those who are seasoned veterans, I apologize for the lengthiness of the write up. You can just download and...

Considering PINDA V2 sensors aren't very expensive, I'll probably just order one of those! Print instructionsCategory: 3D Printer Parts Summary I've been enjoying using the stock inductive Z endstop as a bed probe on my Artillery Genius, but was...

Cómo configurar los parámetros para personalizar la impresión del soporte de maleta para silla de ruedas V2 2.1. Para poder personalizar el soporte de maleta deberá tener instalada en su ordenador la aplicación para diseño 3D OpenSCAD. Se trata de...

The Gryphon is a mostly 3D printable, hobby-grade, Nerf semi-automatic flywheel blaster. Its main design features are as follows:Uses 130 to 180 sized 20.4mm , brushed DC motors.Semi-auto by rack and pinion with 1:3 gear multiplication. The trigger...

... Now I could home the printer and send it to 0,0,0 and the needle should go right to the front left corner which it did.Print SettingsPrinter:Qidi X-ProRafts:NoSupports:NoResolution:.15Infill:20Filament: Hatchbox PLABlackCategory: 3D Printer Parts

Also this shape is very special because you can use two V Plate and invert one to create a sort of "wave" that visually connect two I plate that is place up and down.Double C Plate* : This isn't a stand alone plate, this mean this plate is useless on...

GND should be handled in the ribbon connector. Print instructionsCategory: 3D Printer Accessories Summary I like that the Artillery printers come with an RGB LED on the hotend. It's a nice touch! But what if it could be... Brighter? And more...

A take on norwegiancreation's PID ball balancing seesaw using an Arduino.Video of this...

Average those two altitudes, to get your result (we rotate and average to cancel out any errors due to the ring not hanging perfectly straight).Avoid windy days if you can't move out of the wind, as the ring blowing around reduces accuracy...

If you encounter any layer separation or odd layer squish patterns that were not there before, ensure that the anti-wobble is not allowing any movement in the Z axis direction and adjust accordingly to make sure the pins cannot move up or down. ...

There is now an uploaded drilling guide that takes that into account. Update 8: The long awaited instructions document is now uploaded! Update 9, uploaded an updated Taz 6 specific endplate. There are several other related projects that are...

3d.) Use razor blade to clean up hole and surface (to make surface flat) 3e.) Remove all leftover magnet pieces blocking screw head. 3f.) Carefully clip zip ties holding bed wires to carriage. DO NOT clip wire (Obviously) 3g.) Remove four bed...

... loading filament on each lane to test if the chamfers cut on the smaller tubing is enough to prevent the filament from getting stuck, and to see if the small tubing is seated correctly. Rechamfer/reseat as required Category: 3D Printer Accessories

[ ] 3D Print included stl files [ ] sunlu_fan_mount.stl -- Mounts 50mm blower fan and thermistor to rear of fan case. [ ] sunlu_gauge_ring.stl -- circular slip ring for mounting the hygrometer to the front of the case. [ ]...

or it will sag and make contact with y-front/back-plate !)4x P-112-MINI-y-carriage-bearing-strap.stl Print settings:3 Perimeters4 top/bottom layers0.2mm layer height40% infillMay require custom support(brushed support enforcer in prusaslicer works...

If you want detailed instructions with pictures, please see my instructable on http://www.instructables.com/id/The-Bicycle-Bubble-Machine/ Apart from printed parts, you will need: a piece of wood to mount the machine on, which will then be put onto...

You have to look very carefully at the top side to see that it is 3D printed. That said, I think I prefer the look of the first version. It is more special with the black part laying on top of the white background.</li></ol><p>Note that the .stl...

- 3D Printing is about beauty and design. When storing the filaments visibly, the storage should at least satisfy some degree of beauty. When designing parts to be printed, you also need to take care of the print process: - The print...