ft simple cub 3d models

... For me PETG works perfectlyLayer Height: 0.2mmPerimeters: 4Seam Position: RandomOrientation: Cup with bottom part on print bed, cap upside-down with text on print bedSupport: NoMulti-Color PrintingIt's quite simple to create multi-color pods (i.e.

Since I want as little weight as possible on the cantilever, a simple manual z-axis is the least weight. These are sized for the NEJE 6W laser with 16mm hole spacing horizontal & 48.4mm spacing vertically. Print...

Watch the video above to see how it works.I opted for a simple frame design because A. I prefer that aesthetic and B. a smooth finish is way easier to sand and paint. I may add fancier styles at a later date if people request them. The artwork...

Have fun! Print instructionsCategory: Toys & Games Print Settings Printer: BobsCNC RP9 v2 Rafts: Doesn't Matter Supports: No Resolution: 0.2mm Infill: 25% or more Notes: This should be a simple print. There is minimal bridging and as long as you...

If you do not get a strong clamping force with this simple test, then you probably have one of the magnet faces reversed.If desired, the plate assembly can now be inserted into the Carrier.  Note that the opening in the Carrier has a wide end...

The Flexpoint sensors are exceptionally repeatable and can be read with a simple resistor divider and modern ADC.\nNo thumb?\nThe thumb was intentionally left out to maintain manual dexterity. Wearing this sensor on the thumb would cover the tip and...

If you wear the straps on top of the head, you can still attach an elastic in the vertical slots, or get creative and use Velcro strips or even simple zip ties. This face shield requires a front foam piece, otherwise it can be uncomfortable to wear...

Also countersinking the inner end might be beneficial for the air flow.Update 2022-03-07 / laser-mount_v2.1:Improvements on the additional air assist:increased diameters for inlet pipe diameter and inner channeloutlet hole is now angled so that the...

The jheads and mounts should be pretty self-explanatory as they are simple. You can swap the fender washer and screw holding it for a countersunk magnet and a screw that fits into the countersink for extra tool docking force. I found this helpful. I...

With simple modifications to one of the 5 pieces, it can accommodate pretty much any tablet/phone quickly. You take no responsibility if your prints are insufficiently solid and drop the tablet on the floor! (see instructions for tips). You will...

------------------------------------------------------------------------------------------------------------------------ PSU COVER This is a simple cover that bolts onto the PSU to keep the terminals covered up and safe. It is also designed to reuse...

Existing mounting holes include the mounting pattern for the Larson Electronics LED emitter bars, LED spreader light bars, High Intensity Discharge (HID) equipment lights, HID boat lights and LED spotlight bars and all manner of off road and vehicle...

Sturdy fixing point for all the cables with the use of a simple M3 screw of about 20mm 11. Fixing holes of the old Air System left free if you need to fix an automatic bed levelling device (BL touch of similar) 12. Slight noise reduction of fans...

I've used a simple pin connector glued on Body_B, so when I remove the dust collector I can disconnect the led wiring. There are pictures showing this above.</p> <p>I've connected the circuit to a 12v connector on the router board with a switch...

In simple terms, this could allow specific colors to be printed or used in different locations for better effect and accuracy of a customized iPhone case pattern. ```python ncustom_left_port_y_position = 0\ncustom_right_port_y_position = 0 ``` ###...

Model which I used to test multicolor printing within the same layer using single extruder printer.THIS IS AN EXPERIMENTPROCEED AT YOUR OWN RISKThe idea was simple:We can create multicolor prints on single extruder single filament printers with tools...

Check it out: cyclic: https://www.thingiverse.com/thing:2795753 simple collective: https://www.thingiverse.com/thing:2630031 dual throttle collective with switch panel mount: https://www.thingiverse.com/thing:2747131 pedals:...

To orientate the inflatable structure a bevel gear design would be used around the vertical axis and a simple pinion gear design for the horizontal axis, which would be covered by MLI attached to the back of the moving solar/ inflatable support...

As the power supply has both the air intake and exhaust on the bottom, I've added a simple 'duct' to redirect the warm air to the front of the printer, away from the intake. If you look carefully in the pictures, you'll see that I have removed the...

In order to keep the assembly of mirrors as simple as possible, a system has been designed to fold as few times as possible (to reduce the increase in the number of actuators and implicitly to reduce the complexity of the model). The ability of...

*Top_Cap_Simple.stl: Motor and BMG mount. Bolts to the top of Y-Carriage. No add-ons *<strong>Top_Cap_ZipTie.stl</strong>: Motor and BMG mount. Bolts to the top of Y-Carriage. Prints with sidecar that allows wiring to be zip tied to mount. Bolts to...

In order to keep the math simple, transducer placement is done assuming you want to organize a collection of circles in concentric rings on a sphere, which is not an airtight abstraction. This also notably does not involve any hexagonal packing like...

The basic facial rigging supports simple facial expression creation, such as winking, breathing, adipose trembling, etc. And more … Features "The model is in meter units at real-world scale. The rigged version is in the initial pose, previews are...

The Corner pulley guide have had a simple change made - the fixing hole nearest the corner of the frame has been moved a couple of millimetres to clear the screw head. This allows the T-nut to turn and lock into place so an otherwise excellent...

I got inspiration from: https://www.thingiverse.com/thing:3796938 and thought that this was a extremely clean and simple answer to adding a second Z stepper &amp; leadscrew to my Anycubic Mega Zero 2. Having tried many other designs to attempt this...

This simple and effective approach helps avoid wasting batteries by accidentally leaving it on at the end of the day. The design is easy to 3D print, requiring no supports, brims, or rafts. The source files are published openly on OnShape.com so you...

This is a pretty simple design I made, I was trying to organize my desks cables and I couldn't find a any zip ties or Velcro cable ties, I was also bored so this was created. These are as economical as zip ties while being as reusable as Velcro...

Wiring is simple: servos and laser all lead to a common ground on the board; I used the other ground for the battery snaps' negative, I used 3V3 to the toggle switch to the laser diode. Lift servos trigger wires lead to D10 and tilt servo leads to...

The focuser works by sliding the eyepiece in and out - a light, simple solution that works quite well.The magnification of the telescope is given by the focal length of 900 mm divided by the focal length of the eyepiece. An eyepiece with 10 mm is a...

I Designed This Model Using FreeCad 3D Modeling Software This model was created using simple shapes and techniques offered by the program. Project Name: Delta Rocket - RC Glider or EDF Jet I designed this model as a unique combination of model...