ft aura 5 3d models

This is a filament holder bracket designed specifically for use with the Folgertech FT-5 R2 stock extruder, which features a unique Reverse-Bowden configuration. The bracket is threaded to accommodate 6mm push-fittings, similar to those found in this...

The compact bowden carriage for the Folgertech FT-5 is only 3mm in diameter, allowing for the full bed size of approximately 310x310x415 to be utilized. This design has been specifically tailored to work seamlessly with a genuine E3D v6 hotend, which...

Here's a modification to the source file designed to make it compatible with the Folgertech FT-5 stock extruder, with fingers crossed! I haven't printed this yet, but I'd love to know if anyone likes it and more importantly, if my adjustments are on...

This is a 3-piece cooling set for the stock hot end of the FolgerTech FT-5. The 50mm fan bracket was designed specifically around this fan: http://goo.gl/xNLN74. The C-Cooler bracket was initially created in version one, providing a basic setup for...

The replacement FT-5 also has a deeper shaft to accommodate the additional bolt length due to the counter-sink.\nPrint Settings\nPrinter: \n FT-5\n \n Rafts: \n Doesn't Matter\n \n Supports: \n Doesn't Matter\n \n Notes: \n Easy to print, no special...

This remix of the PoseidonAudio RJ45 Breakout board for the FT-5 integrates seamlessly with the 713 maker gantry, but my design deviates slightly as the blocks are stacked vertically rather than on either side. To accommodate the breakout board, I...

This is an optical Z endstop designed specifically for use with the Folger Tech FT-5. ...Made to function seamlessly with a PC expansion slot cover trimmed down to approximately 35mm, it effectively blocks light from entering.\nA slight drawback is the...

This is a mount for the E3D Hemera for the FolgerTech FT-5, it includes a fan duct for a 5050 blower and a bl touch mount. This is setup and working on my printer at the moment. The mount can be printed in any orientation which suits you. ...

I was fed up with wrestling with the timing belt on the FT-5 carriage, so I came up with a solution. This was a clever combination of my previous designs. It should work seamlessly with the other stock carriage parts, but I would suggest downloading...

After modifying it to accommodate some 2.5" props, the difference was like night and day - a world of difference that's for sure. So, I took the next logical step by modifying the frame for 2.5" props, and now I'm sharing my creation with all of you....

I crafted this design specifically for my Folger Tech ft-5 3D printer, knowing I'm not a master designer, but hoping it will still prove useful when you need to move your large printer. ... To assemble the extra part, you'll require: * Handles that can...

I took the FolgerTech FT-5 Adjustable Glass Holder design as a starting point, but instead of using 3mm square nuts, I opted for heat-set inserts. This version is essentially an upgraded iteration of the original, boasting a slightly taller profile...

I built this for my Folgertech FT-5 v2. It holds my Bondtech BMGx2 to my E3D Chimera in a direct drive setup. Simply screw the two units together, insert them into the rig, and then screw the steppers onto the extruder to secure everything on the...

Printer Settings Printer: FolgerTech FT-5 Rafts: No Supports: No Resolution: 0.2mm Infill: 25% Notes: After printing, use a small drill to make sure the filament feed holes are wide enough to reduce friction. Use pliers and a little bit of...

The replacement FT-5 also has a deeper shaft to accommodate the additional bolt length due to the counter-sink. Print Settings Printer: FT-5 Rafts: Doesn't Matter Supports: Doesn't Matter Notes: Easy to print, no special settings needed. Suggest...

This is a long-overdue solution for the Folger Tech FT-5 "Z" axis home switch. I was fed up with struggling to hold those tiny nyloc nuts, so I designed the switch clamp with built-in nut holders. The "Z axis screw clamp" is engineered to fit snugly...

... After Printing - I've Achieved Successful Results Using Crazy Glue. This Update Focuses on Enhancing Airflow to the Part. Print Settings: Printer: FT-5 Rafts: None Supports: Yes Infill: 50% How I Created This Design: Using Autodesk Inventor

Print Settings Printer: Printy McPrintface (FT-5) Rafts: No Supports: No Resolution: 0.3 Infill: 40% or more Notes: For optimal results, print out of PETG or ABS for strength and heat resistance. ... Post-Printing No post-processing is required; the...

While searching for a reliable heatsink and nozzle cooling solution that still accommodates fitment of a BLTouch on my FT-5, I discovered several excellent ideas. However, merging them all into one cohesive design was the main challenge... What you...

While searching for a reliable heatsink and nozzle cooling system that would still allow fitment of a BLTouch on my FT-5, I discovered several excellent ideas. Integrating them into one cohesive design was the only challenge... What you see here is a...

Given the high travel speeds of the x-y carriage on an FT-5, I didn't feel it was a good idea to let the same movement also unwind a heavy filament spool at the same time. I also own a Kossel, which has a a bowden setup where the extruder is mounted...

I'm running a remix of printingotb's OptiCooler for the Folger Tech FT-5, which I'm currently pairing with the 713Maker Ultralight carrier and stock MK9 hotend. This configuration may also work with the Titan Aero extruder. The fan bracket attaches...

A simple yet effective upgrade for the FT-5 printer involves replacing the stock screen and plate with a custom knob and e-stop button. The replacement knob is designed with precision in mind, boasting an ideal length that suits most users' needs. To...

I'm reworking a printer setup based on printingotb's OptiCooler design, specifically tailored for the Folger Tech FT-5. Currently, I'm running the 713Maker Ultralight carrier paired with the stock MK9 hotend; however, it may also be compatible with...

This is a face plate for the Folger Tech FT-5 RepRap graphics controller. The holes on this part are slightly irregular, requiring some modification before assembly. I'm still working on this design. An online model repair issue led to these...

This modification is specifically designed for the FT-5 R2 version, which already features a single Z-Axis drive motor. To implement this change, you will need to replace the Z-Axis drive belt and the two pulleys on the Z-Axis drive screws. In...

Print settings are also provided, including: * Printer: FolgerTech FT-5 * Rafts: Doesn't Matter * Supports: Doesn't Matter * Resolution: 0.200mm * Infill: 85-100 percent * Hotend Temp: 232 C * Bed Temp: 64 C * Wall thickness: 2mm The instructions...

Optional: I designed two different ring clamps to hold the pipe itself in place on the brackets & to hold the spool in place on the pipe.\r\n\r\nAll you need to print for this is the pair of brackets, which are designed to mount with the same M5x10mm...

I'm personally using the FT11 and FT13/14 replacement from this set along with the FT13 bottom and FT12 from this fan duct set (white parts in the images): http://www.thingiverse.com/thing:1666994 Print Settings: Printer: FT-5 Notes: I recommend high...

Wheel set with tread tires for Sturmkind DR!FT Racer The wheels are larger than the original wheels. ... The tire diameter is 16.5mm Not for commercial use, only for private use!